Bosch Rexroth IPC Connectivity Manual Download Page 46

Page: 46 / 99

Electrical Connections

5–8

1070 073 822-104 (02.06) GB

5.3.2

230/115 VAC power supply

X20

230/115 VACpower connection (w/ integrated AC power supply)

Alternative to 24 VDC power connection.
All internally required voltages are produced by the integrated power supply.

CAUTION
The supply voltage must satisfy the requirements of Overvoltage
Category II. Otherwise, the integrated power supply may be de-
stroyed.
Use a separation transformer to generate the 230/115 VAC (refer to
next page).

Coupler for non-heating apparatus, 3-pin

Max. conductor cross0section:

1.5 mm

X20

Assignment

Rated voltage:

85VAC to 264VAC;
Extended-range input

Current draw at U

= 230 VAC:

0.6 A

Current draw at U

= 115 VAC:

1.2 A

Inrush current

at 230 VAC:

30 A, cold start 25

at 115 VAC:

15 A, cold start, 25

Input fuse:

1.25 A (5x20) medium time-lag

Summary of Contents for IPC




































































































Search results

Summary of Contents for IPC

Reviews:

Related manuals for IPC

Brands by name

Popular brands

Bosch Rexroth IPC, Connectivity Manual

Search results

Summary of Contents for IPC

Reviews:

Related manuals for IPC

Brands by name

Popular brands