Bosch Rexroth CDT1 Series, Manual

Page: 25 / 44

RA 17038/02.13 | CDT1/CGT1 Industrial Hydraulics | Bosch Rexroth Corp. 25 /44
Bore Rod
In. In. V W Y ZJ ZT
1.500 0.625 0.25 0.63 1.94 4.63 5.62
1.000 0.50 1.00 2.31 5.00 6.00
2.000 0.625 0.25 0.63 1.94 4.63 5.75
1.000 0.50 1.00 2.31 5.00 6.12
1.375 0.63 1.25 2.56 5.25 6.38
2.500 0.625 0.25 0.63 1.94 4.75 5.88
1.000 0.50 1.00 2.31 5.13 6.25
1.375 0.63 1.25 2.56 5.38 6.50
1.750 0.75 1.50 2.81 5.63 6.75
3.250 1.000 0.25 0.75 2.38 5.63 7.00
1.375 0.38 1.00 2.63 5.88 7.25
1.750 0.50 1.25 2.88 6.13 7.50
2.000 0.50 1.38 3.00 6.25 7.62
4.000 1.000 0.25 0.75 2.38 5.63 7.00
1.375 0.38 1.00 2.63 5.88 7.25
1.750 0.50 1.25 2.88 6.13 7.50
2.000 0.50 1.38 3.00 6.25 7.62
2.500 0.63 1.63 3.25 6.50 7.88
5.000 1.000 0.25 0.75 2.38 5.88 7.69
1.375 0.38 1.00 2.63 6.13 7.94
1.750 0.50 1.25 2.88 6.38 8.19
2.000 0.50 1.38 3.00 6.50 8.31
2.500 0.63 1.63 3.25 6.75 8.56
3.000 0.63 1.63 3.25 6.75 8.56
3.500 0.63 1.63 3.25 6.75 8.56
6.000 1.375 0.25 0.88 2.78 6.63 8.44
1.750 0.38 1.13 3.03 6.88 8.69
2.000 0.38 1.25 3.16 7.00 8.81
2.500 0.50 1.50 3.41 7.25 9.06
3.000 0.50 1.50 3.41 7.25 9.06
3.500 0.50 1.50 3.41 7.25 9.06
4.000 0.50 1.50 3.41 7.25 9.06
Bore SAE Port NPT Port
In. E EE EE F G J K AA BB DD LB P
1.500 2.00 -6 3/8 0.38 1.50 1.00 0.25 2.02 1.00 1/4 - 28 4.00 2.2
2.000 2.50 -6 3/8 0.38 1.50 1.00 0.31 2.60 1.13 5/16 - 24 4.00 2.28
2.500 3.00 -6 3/8 0.38 1.50 1.00 0.31 3.10 1.13 5/16 - 24 4.13 2.38
3.250 3.75 -10 1/2 0.63 1.75 1.25 0.38 3.90 1.38 3/8 - 24 4.88 2.69
4.000 4.50 -10 1/2 0.63 1.75 1.25 0.38 4.70 1.38 3/8 - 24 4.88 2.6
5.000 5.50 -10 1/2 0.63 1.75 1.25 0.44 5.80 1.81 1/2 - 20 5.13 2.9
6.000 6.50 -12 3/4 0.75 2.00 1.50 0.44 6.90 1.81 1/2 - 20 5.75 3.16
Dimensions MX1, MX2, MX3
Tie Rod and Flange Mounts are basically the
same except that the tie rods are extended and
used to mount the cylinder. To prevent misalign-
ment, sagging or binding of the cylinder when
long strokes are required, the free end of the
cylinder should be supported. For thrust load
applications, blind or cap end tie rod extensions
are best. For tension load applications, rod or
head end extensions are best. Tie rod mounts are
suited form any applications, however it should
be noted that they are not as rigid as the flange
mountings.
NOTE: The bearing retainer plate is the same as
the “E” dimension for the 1.5” – 6” bore sizes.
Rod end options shown on page 6.
Table 1 - Dimensions affected by rod diameter
Table 2 - Dimensions not affected by rod diameter