background image

10/19

 

CH16NFT

 

 

                

Made in China to TQB Brands Pty Ltd specifications 

 

P a g e

 | 2 

Visit us at www.tqbbrands.com.au

 

STANDARD OPERATING PROCEDURE 

DO NOT use this machine unless you have been trained and assessed to a competent level in its safe use and operation, and 
have been given permission to use this  

 

 

PRE-OPERATIONAL SAFETY CHECKS 

1.

 

Keep guards in place and in good working order 

2.

 

Keep drill press in good working order, follow lubricating and changing accessories instructions 

3.

 

Use recommended accessories only, failure to do so may damage the drill press and/or may risk 
injury 

4.

 

Remove adjusting keys & wrenches from the drill press before operating 

5.

 

Ensure the switch is in the OFF position before starting the drill press 

6.

 

Disconnect drill press before performing any maintenance 

7.

 

Keep work area clean, free from hazards and well lit. 

8.

 

Only use the drill press for its intended purpose. 

9.

 

Wear the correct PPE clothing.  

10.

 

Secure work using claims or vice where practical. 

11.

 

Do not overreach, keep proper footing and balance at all times while operating the drill press 

12.

 

Never leave drill press running unattended, always lock the “on – off” switch when not in use  

13.

 

Use only on hard level surfaces capable of sustaining the load.  

14.

 

Ensure that risk assessment has been read.   

15.

 

Check workspace and walkways to ensure no slip-hazards are present. 

16.

 

Faulty equipment must not be used.  Immediately report suspect equipment. 

 

OPERATIONAL SAFETY CHECKS 

1.

 

Never leave the machine running unattended. 

2.

 

Before making adjustments or before cleaning sward accumulations switch off and bring the 
machine to a complete standstill. 

3.

 

Ensure that the work piece is securely held in a clamped work vice or clamped directly to the 
table. 

4.

 

Feed downwards at a sufficient rate to keep the drill cutting. 

5.

 

Feed with care as the drill breaks through the underside of the work. 

6.

 

Use a safe working posture (beware of hair catching). 

 

HOUSEKEEPING 

1.

 

Switch off the machine. 

2.

 

Return all tooling and fixtures to the correct storage location. 

3.

 

Display a completed “Equipment in Use” notice if the machine is set up and/or in use but 
unattended. 

4.

 

Leave the machine and work are in a safe, clean and tidy state after job is completed. 

5.

 

Return surplus material to stock and dispose of waste material in an appropriate recycling or 
waste bin. 

 

POTENTIAL HAZARDS 

 

Hair/clothing entanglement – rotating spindle/drill 

 

Flying swarf/chips 

 

Eye injuries 

 

Sharp edges and burrs 

 

High noise levels when drilling some materials 

 

Distracting operator 

 

Removal or modification of safety devices 

 

Using equipment with lapsed test tag 

 

Safety glasses must be worn when 
operating this equipment 

 

Long loose hair must be contained when 
operating this equipment 

 

Safety footwear must be worn when 
operating this equipment 

 

Close fitting/protective clothing must be 
worn when operating this equipment 

 

Rings and jewellery must not be worn 
when operating this equipment 

 

Hearing protection must be worn where 
noise levels are in excess of 85 dB(A) 
occupational exposure limit 

 

Gloves must not be worn when 
machine is operating.  Machine to be at 
standstill if gloves required for manual 
operations. 

 

 

Summary of Contents for CH16NFT














Reviews: