The amplifier shall be a Bogen Wall-Mount Power Vector
Amplifier, Model WV
1
00,WV
1
50 or WV250.The amplifier
shall be compatible with both high- (70/25V) and low- (4/8-
ohm) impedance speakers, with the capability of
1
00,
1
50,
or 250 watts, respectively.
The amplifier shall provide 8 module bays for plug-in input
modules with two of the bays also capable of handling plug-
in signal processing output modules.There shall be 4 levels
of priority between modules.
Each of the 8 module bays shall have an associated inde-
pendent volume control. Each independent volume control
shall have a signal/clip LED to indicate if a clipping condition
is occuring at the module’s output. Each amplifier shall also
include detented bass and treble controls, as well as a
motorized master volume control, which can be remotely
operated using the RVCP accessory (sold separately).
The amplifier shall include an adjustable output level limiter
with indicator LED.A tape output jack shall be available on
the front panel and an optional front panel input combo
jack with
1
/4" stereo phone and female XLR capabilities
may be installed.
Screw terminals shall be provided for invoking a master
mute function that will interrupt all audio from the mixer
section of the amplifier.
An
11
-segment LED output level meter will register either
the average or peak level of the amplifier’s output level,
determined by an Average/Peak switch. Each amplifier shall
have a Tone Control Bypass switch and a Low-Cut Filter
switch located on the rear of the amplifier in module bay 6.
A switch will permit the selection of transformer-coupled
output or direct output for speaker runs. Master mute and
remote volume control functions are controlled using a
screw terminal.
The amplifier shall be flush-mounted or surface-mounted
into a wall using either a BBF or BBS back box (sold sepa-
rately). A front cover door shall be required (WMAD sold
separately). Each model shall measure
1
4-
1
/8" W x 2
1
" H.
The WV
1
00 shall weigh 27 lb.; the WV
1
50, 29 lb.; and the
WV250, 28 lb.
Architect and
Engineer
Specifications
50 Spring Street, Ramsey, New Jersey 07446, U.S.A.
20
1
-934-8500 FAX: 20
1
-934-9832
Web Site: www.bogen.com
Technical
Specifications
Power Output (RMS)
WV
1
00:
1
00W (
1
40W Typical, @
1
kHz/0.
1%
/4
Ω)
WV
1
50:
1
50W (200W Typical, @
1
kHz/0.
1%
/4
Ω)
WV250:
250W (340W Typical, @
1
kHz/0.
1%
/4
Ω)
Frequency Response
Transformer:
45-20 kHz; 0/-2 dB @ FRP
Direct:
20-20 kHz; 0/-
1
dB @ FRP
Distortion
Transformer:
0.5% THD+N, Maximum,
Full-rated bandwidth @ FRP
Direct:
0.
1
% THD+N, Maximum,
Full-rated bandwidth @ FRP
Signal-to-Noise
Fundamental:
-94 dB*
With Aux Module:
-70 dB*
With Mic Module:
-60 dB*
With Tel Module:
-70 dB*
Tone Controls
Bass Frequency:
1
00 Hz (+/-
1
0 dB minimum)
Treble Frequency:
1
0 kHz (+/-
1
0 dB minimum)
Low Cut Frequency:
1
25 Hz @ -6 dB/octave
Sensitivity:
0.4V (at backplane connector)
Output Regulation:
2 dB or better no load to full load
Output Impedance
Transformer-Coupled:
70V, 25V, 8 ohms; balanced or unbalanced
Direct Coupled:
4 ohms unbalanced
Tape Out
Output Level:
4 VRMS @ FRP
Output Impedance:
50 ohms maximum
Overload Protection:
Electronic overload protection
(auto reset)
Thermal Protection:
Thermistor attached to heat sink
Line Fusing:
Resettable circuit breaker
Cooling:
Thermally controlled 3-speed fan
Power Consumption:
WV
1
00:
2.0A @
1
20V AC, 60 Hz
WV
1
50:
3.5A @
1
20V AC, 60 Hz
WV250:
5.5A @
1
20V AC, 60 Hz
Dimensions:
WV
1
00/
1
50/250:
1
4-
1
/8" W x 2
1
" H
BBF:
1
4-
1
/2" W x 24-3/4" H x 3-7/8" D
BBS:
1
6-
1
/4" W x 26-3/4" H x 3-7/8" D
WMAD:
1
6-
1
/4" W x 26-3/4" H x
1
" D
Product Weight:
WV
1
00:
27 lb.
WV
1
50:
29 lb.
WV250:
28 lb.
BBF:
1
4 lb.
BBS:
1
8 lb.
WMAD:
11
lb.
* Referenced to full-rated power (FRP) output level, 20-20 kHz bandwidth limited.
All specifications subject to change without notice.
