One Series,
Various Installation Needs
Performance
Specifications
Bogen’s M-Class delivers on what contractors need most:
•
Reliability -
Massive power toroid and heat sinks, heavy 14-gauge chassis, Back-Slope™ AC voltage
stabilization, Clip limiters, DC voltage, over-current and thermal protection circuits.
•
Flexibility -
3 modes of operation: 70V Mono, Dual Mono, or Stereo; 2 modular input bays
for a variety of prioritized input types.
•
Power -
up to 600W/ch stereo or 1200W of 70V mono power with low distortion and a high slew rate.
All this wrapped into 2 rack spaces of some of the best looking metal in the industry.
Three, Flexible Operating Modes
Flexible operating modes meet different installation needs.
70V Mono Mode
Dual Mono Mode
Stereo Mode
70V Mono Mode:
Provides a single channel of output for
70V constant voltage speaker systems. Inputs form
a 2x1 mixer with the front panel controls determining
the signal levels from each input.
Stereo Mode:
In stereo mode, the front panel controls allow
independent operation of the two power amp channels.
Dual Mono Mode:
Dual mono provides the same mixer
operation as 70V Mono Mode, but with two amplifier
channels for low-impedance speaker systems. A balance
control is provided to adjust the overall volume level
between the two amplifier outputs. Inputs form a 2x1
mixer with the front panel controls determining the signal
levels from each input.
* Both channels driven at nominal line voltage
1
20V AC, 60Hz. ** Module set to Gain of
1
. *** Requires 20A, NEMA 5-20R Type Receptacle.
Technical Specifications
M600
M450
M300
Power Output
70V Mono
4-ohm
8-ohm
1
200W @ 4 ohms
600W per channel*
400W per channel*
900W @ 5.5 ohms
450W per channel*
300W per channel*
600W @ 8 ohms
300W per channel*
200W per channel*
Input Sensitivity
At Backplane Connector or using
Standard Input Module (incl.)**
1
.
1
6
1
V for 600W @ 4 ohms
1
.0
1
0V for 450W @ 4 ohms
0.840V for 300W @ 4 ohms
S/N Ratio (20K BW)
1
09 dB ref. 8 ohms, F.P.
1
06 dB ref. 8 ohms, F.P.
1
03 dB ref. 8 ohms, F.P.
Class of Operation
H
H
AB
Product Weight
46 lb.
44 lb.
4
1
lb.
Connectors:
Power
Input
Output
20A line cord***
1
5A line cord
1
5A line cord
Dependent on Modules installed (stereo, high-impedance balanced module w/screw terminals included)
5-pin "touch-proof" Barrier Strip, RCA Pre- & Post-EQ Output
Power Bandwidth
20 Hz - 40 kHz .5% THD
THD @
1
kHz rated power
less than .02%
Load Impedance
4-8 ohms, 70V
Minimum Load Impedance (Stereo)
2 ohms
Frequency Response @
1
watt
20 Hz - 20 kHz +/- 0.25 dB
Output Regulation,
1 kHz direct
1 kHz bridged
0.5 dB @ 8 ohms
1
.5 dB @ 70V
Inputs (Plug-in modules)
Electronically balanced, high-impedance module standard, other modular input types available
AC Input Voltage Range
95-
1
30V AC, 60Hz
Maximum AC Current
20A***
1
5A
1
2A
Indicators
Status (On/Protect/Sleep), Clip/Limit, Signal
Temperature Range
1
5 to
1
05 degrees F
Cooling
Forced Air Variable Speed Fan
Physical Dimensions (W x H x D)
1
7" X 3-
1
/2" x
1
6" (
1
9" wide with Rack Ears)
Protection
RF, DC, Low-frequency, Thermal, Low-Impedance, Circuit-Breaker, Short Circuit
Special Features
Sleep Mode, Back-Slope regulation, Stereo, Dual Mono, 70V Mono Operation, Toroidal Power Transformer
Accessories
RPK86
Rear Rack
Mounting
Kit
PVMC
Module
Security
Cover
