background image

Bogen Classic Series Amplifiers are warranted to be free from defects in material or workmanship for two (2) years from the date
of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes
defective will be repaired or replaced by Bogen, at our option, provided the product is shipped insured and prepaid to: Bogen Factory
Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The product will be returned to you freight prepaid. This warranty
does not extend to any of our products that have been subjected to abuse, misuse, improper storage, neglect, accident, improper
installation or have been modified or repaired or altered in any manner whatsoever, or where the serial number or date code has
been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PUR-
CHASER’S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND,
EITHER EXPRESS OR IMPLIED,AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT
ALLOWABLE BY LAW.

Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition,

whether based upon warranty, contract, tort or otherwise, shall be limited to the price of the product. In no event shall Bogen be
liable for special, incidental or consequential damages (including, but not limited to, loss of profits, loss of data or loss of use dam-
ages) arising out of the manufacture, sale or supplying of products, even if Bogen has been advised of the possibility of such damages
or losses. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from
State to State.
Products that are out of warranty will also be repaired by the Bogen Factory Service Department -- same address as above or call
20

1

-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by the Bogen Factory Service

Department. All shipping charges in addition to parts and labor charges will be at the owner's expense.All returns require a Return
Authorization number.

Accessories

RPK50 - Rack Mounting Kit

Adapts Classic Series amps (Models C35, C60, and C

1

00) for 

1

9" rack

mounting, 2 rack spaces (3-

1

/2")

Heavy gauge steel construction

Warranty

10

WMT

1

A - Matching Transformer

Hi-Z,

1

0k-ohm primary impedance

Lo-Z, 600-ohm secondary impedance, balanced with center tap

Matches high-impedance unbalanced or low-impedance balanced signals

Jumper selection allows line level signal to microphone level 
signal conversion

50 Spring Street, Ramsey, NJ 07446, U.S.A.

Tel. 201-934-8500, Fax: 201-934-9832, www.bogen.com

Summary of Contents for Classic C100













Reviews: