Bofa AD 350 Operation Instructions Manual Download Page 11

Page: 11 / 18

Version 10.08.2011

OPERATION

Manual operation

Stainless steel

AD units are turned on by depressing the green button on the front of

the extractor and turned off by depressing the red button. (See fig 9). Powder coated
AD

units are turned on and off by means of a green, illuminated rocker switch on the

rear of the unit, (See Fig 9).

Fig 9

Filter condition and System failure signal - indicators

The

LED’s on the front panel (see table below) indicate the following conditions

LED’S

SHOWING

INDICATES

Green Only

Unit is running - Filters are usable

Green & Amber

Pre or Combined Filter 75%
blocked

Green, Amber & Red

Pre or Combined Filter Blocked
and in need of replacing

Green, Amber & Red flashing

Fault with extractor.
This condition may occur for a few
seconds on start up

Red Alarm Light

Only used with optional extra Gas
Filter Change LED

Filter change procedures are explained in the Maintenance Section.

Summary of Contents for AD 350



















Search results

Summary of Contents for AD 350

Reviews:

Related manuals for AD 350

Brands by name

Popular brands

Bofa AD 350, Operation Instructions Manual

Search results

Summary of Contents for AD 350

Reviews:

Related manuals for AD 350

Brands by name

Popular brands