BodyCraft MINI-XPress 7351 Instruction Manual Download Page 11

Page: 11 / 11

Assembly is complete! Please take the following steps before using the gym:

Make certain all bolts are tightened securely.

Make certain all cables are seated into all pulley grooves. A cable rubbing

against steel will peel the nylon coating, voiding warranty and resulting in a

need for replacement.

Pre-stretch the cables. Put the Weight Selector Pin (42) in the bottom hole on

the weight stack. Pull on the cables with great force, helping remove any

kinks and providing any initial cable stretch.

Be aware the cables can loosen and slightly stretch upon initial use.

The cables should be adjusted as tight as possible, but no so tight as to lift

the Top Plate (17) above the weight stack. Be certain to secure the jam nuts

after adjustments are made.

For better performance, apply a household lubricant (such as silicone) to any

adjustable areas and to the Guide Rods (5).

Enjoy many years of a Fit Lifestyle.

Thank you for purchasing the MINI X Press Gym. If You have any

questions, please call your local BodyCraft dealer or call our

customer service department at 800-990-5556

Summary of Contents for MINI-XPress 7351











