background image

W5

W4

W6

W3

W2

W1

144

147

101

5

W6

144

147

5

101

W5

W4

101

170

134

25

C5

W1,W2,W3

245

212

202

W3

W2

W1

Leg  Press  Low Cable (213B)

Ball End

Threaded End

Assemble cables and pulleys simultaneously.

 

1. Screw the threaded end of the Leg Press Low Cable 

(213B) into the threaded receptor welded to the vertical 

tube on the Connecting Rear Stabilizer (202).  Then route 

the cable around pulley W2 which is mounted to the 

Sliding Pulley Block (207) using 3/8" X 1-3/4" Hex Bolt 

(231) and 3/8" Nylon Nut (237).  Then route under pulley 

W3 mounted using 3/8" X 1-1/2" Hex Bolt (245), as 

shown in Fig. W1,W2,W3. 

2. Continue routing cable up and around pulley W4 mounted 

to the bottom of the Single Pulley Bracket (25) using a 

3/8" X 1-3/4" Hex Bolt (134) and a 3/8" Nylon Nut (170) 

as shown in Fig. W4. 

The Cable length can be adjusted using the two 

threaded ends                            of the cables.  Be sure to 

always keep                                            the threaded ends 

at least 1/3 engaged.

Do not unscrew the                                              threaded 

ends more than 2/3                                            of their

length.  Always                                                     use the 

jam nut to prevent                                                these

cables from

unscrewing.

STEP  4  INSTALL LEG PRESS LOW CABLE

7

Summary of Contents for MA6053










Reviews: