218
218
241
205
241
241
238
238
238
226
206
208
226
240
237
238
234
211
217
238 234
224
236
239
238
238
230
209
210
220
214
203
216
216
204
236
236
216
227
207
240
212
228
237
237
215
215
201
239
238
238
234
202
231
229
238
229
238
238
241
236
240
STEP 2
-5-
225
1. Attach the Leg Press Main Frame (202) to the Weight Base Connector (207), using two 3/8" X
4" Hex Bolts (229), three 3/8" Washers (238) and one 3/8" Nylon Nuts (241). One nut welded
on Weight Base Connector End (207) to Leg Press. Attach the Long Leg Press Connector
(205) to the Leg Press Main Frame (202), using two 3/8" X 4" Hex Bolts (229), four 3/8"
Washers (238) and two 3/8" Nylon Nuts (241).
2. Attach the Base Stabilizer (201) to the Leg Press Main Frame (202) using two 1/2" X 3-1/4"
Hex Bolts (227), four 1/2" Washers (237) and two 1/2" Nylon Nuts (240). Attach a 45 X 75mm
Rect. Cap (214) to the bottom rear of the Leg Press Main Frame (202). Attach a 50 mm Sq.
Caps (215) to each end of the Base Stabilizer (201).
3. Slide a Bearing Housing (212) onto each end of the welded axle on the Rear Leg Press
Support (208) and then bolt the Bearing Housings (212) to the Leg Press Main Frame (202)
using four 1/2" X 1-3/4" Hex Threaded Bolts (228), eight 1/2" Washers (237) and two 1/2" Nuts
(240).
4. Attach the Front Leg Press Support (206) to the Leg Press Main Frame (202) using one 5/8" X
6-1/2" Hex Bolt (226), two 5/8" Washers (236) and one 5/8" Nylon Nut (239).
5. Attach the Foot Plate Connector (209) to the Rear Leg Press Support (208) and the Front Leg
Press Support (206) using one 5/8" X 6-1/2" Hex Bolt (226), two 5/8" Washers (236) and one
5/8" Nylon Nut (239) in each Leg Press Support (206).
6. Attach the Foot Plate (210) to the Foot Plate Connector (209) using two 1/2"
Washers (237) and two 1/2" Nylon Nuts (240). Attach two 45 X 75mm Rect.
Plugs (216) to the Foot Plate (210).
7. Attach the Right and Left Leg Press Handles (203 & 204) to the Leg
Press Main Frame (202), angle facing up, using two 3/8" X 3-1/8" Hex
Bolts (230), four 3/8" Washers (238) and two 3/8" Nylon Nuts (241).
8. Attach the Seat Pad for Leg Press (225) to the Leg Press Main Frame
(202) using two 3/8" X 1" Hex Bolts (234), one 3/8" X 2-3/4" Hex Bolt
(231) and three 3/8" Washers (238). Attach the Back Pad for Leg
Press (224) to the Back Pad Adjuster (211) using two 3/8"
Washers (238) and two 3/8" X 1" Hex Bolts (234).
Screw the Locking Spring Knob (220) into the Leg
Press Main Frame (202) and the slide the Back
Pad Adjuster (211) into the Main Frame (202).
Adjust to the desired position by pulling the
Locking Spring Knob (220).
Tighten all bolts gradually, from
ground - up.
