manualshive.com logo in svg

BodyCraft F602V2, Owner'S Manual, Page: 4 / 6

Share
Download
BodyCraft F602V2 Owner'S Manual Download Page 4

3

Recommended Tools

Utility Knife 

(To cut packaging and banding)

Ratchet with 9/16" and 3/4" Sockets

9/16" and 3/4" Combination Wreches

Adjustable Wrench

Rubber Mallet

Assembly  Instructions

NOTE:  Before installing the plastic parts, please allow them

to acclimate to room temperature or they may be damaged.

CAREFULLY install all plastic components with Rubber Mallet.

PLEASE  REFER  TO  THE  EXPLODED  VIEW  ON  THE  NEXT  PAGE  FOR  ASSEMBLY.

1.  Carefully  install  END  CAPS(21)  onto  FRONT  STABILIZER(2)  and  REAR  

STABILIZER(3)  using  a  rubber  mallet.

2.  Bolt  the  FRONT  STABILIZER(2)  and  REAR  STABILIZER(3)  to the  MAIN  FRAME(1),  

using  four  BOLTS(53),  eight  WASHERS(55)  and  four  NUTS(57).  Tighten.

3.  Bolt  ATTACHMENT  HOLDER(6)  to  MAIN  FRAME(1),  using  two  BOLTS(53),  four

WASHERS(55)  and  two  NUTS(57).  Tighten.

4.  Install  END  PLUGS(23)  into  SEAT  ADJUSTER(5)  and  BACK  SUPPORT(4)  using  a

rubber  mallet.

5.  Attach  SEAT  ADJUSTER(5)  and  BACK  SUPPORT(4)  to  MAIN  FRAME(1),  using

BOLT(51)  and  NUT(57).  (NO  WASHERS)  (Any  moving  parts  that  do  not  pivot  freely,

slightly  loosen  the  nuts  counterclockwise  at  the  pivot  points  to  allow  movement,  but

not  too much  to  allow  play  or  wobble.)

6.  Attach  SEAT  PAD(32)  to  SEAT  ADJUSTER(5)  and  BACK  PAD(31)  to  BACK

SUPPORT(4),  using  BOLT(54),  WASHER(56).  Tighten.

7.  Install  50mm  SPACER  CAP(22)  onto  ATTACHMENT  HOLDER(6).

8.  Insert  LEG/KNEE  HOLD  DOWN(10)  into  ATTACHMENT  HOLDER(6).  Using  Pop-Pin.

9.  Install  END  PLUGS(24)  into  LEG/KNEE  HOLD  DOWN(10)  with  Rubber  Mallet.

10.  Insert  FOAM  PAD  HOLDERS(8)  into  the LEG/KNEE  HOLD  DOWN(10)  and  slide

FOAM  ROLLER  PAD(33)  onto  each  end  of  the  FOAM  PAD  HOLDER(8)  and  secure

with  1"  ROUND  CAP  PLUG(25)  using  rubber  mallet.

11.  Install  KNOB(43)  onto  the  threaded  end  of  the  pre-installed  BOLT(63)  located  at

the  lower  part  of  the  BACK  ADJUSTER(7).  Tighten.

ASSEMBLY  IS  COMPLETE!

PLEASE  RECHECK  THAT  ALL  COMPONENTS  ARE  TIGHT  AND  SECURE.

Summary of Contents for F602V2







Reviews:

No comments