manualshive.com logo in svg

Body Solid EXM2500, Assembly Instructions And Owner'S Manual

Share
Download
Body Solid EXM2500 Assembly Instructions And Owner'S Manual Download Page 28

28

STEP

3B

Be careful to assemble all components 

in the sequence they are presented.

NOTE:

Finger tighten all hardware in this step. Do Not wrench tighten until end of

At this point make sure that the gym is in the right location.

1 . 

Insert (2) Guide Rods 

X

 into the Main Base Frame 

A

 .

 

Insert (2) 2 1/2” Rubber Donuts 

d10

 onto the (2) Guide Rods 

X

 as shown .

 

Slide 20 Weight Stack Plates (one at a time) onto the (2) Guide Rods 

X

 . Make sure the  

 

 

opening in each weight stack plate, for the Weight Stack Pin 

a13

, is facing outward .

2 . 

Attach Top Plate 

d29

 to Selector Rod 

d19

 using:

 

(1) a14   3/8” x 2” round bolt

 

(1) c6   3/8” spring washer

 

Slide Top Plate 

d29

 and Selector Rod 

d19

 onto Guide Rods 

X

 as shown .

3 . 

Slide (2) Shaft Collars 

d35

 onto the (2) Guide Rods 

X

 as shown .

 

Slide Weight Stack Top 

M

 onto the (2) Guide Rods 

X

 and attach Weight Stack 

 Top 

M

 to 2” x 4” Top Frame 

G

 using:

 

(2) a3   1/2” x 3” hex head bolt

 

(2) c1   1/2” washer

 

(2) b1   1/2” nylon locking nut

4 . 

Attach (2) 2” x 2” x 1 .8” End Caps 

d3

 onto Weight Stack Top 

M

 .

 

Insert (2) Shaft Collars 

d35

 into Weight Stack Top 

M

, turn to attach, then tighten  

 

allen bolt in the (2) Shaft Collars 

d35

 .

NOTE:

At this point you must make sure that the gym is level, stable and in the right location.  

You should now wrench tighten all bolts and nuts on the mainframe unit only.

Do NOT re-tighten any of the pad bolts.

STEP

3B

Summary of Contents for EXM2500

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands