1. Place Counter Gasket
over mounting hole
to align with profile of
dispenser.
2. Insert Stem with tube
and all Fiber Optic
Cables carefully through
mounting hole.
3. Place the Wave Washer
on top of the Mounting
Nut. Install Mounting Nut
on Stem and thread
upwards. (Minimum 2-1/4"
(55mm) diameter
clearance needed below
mounting nut).
NOTE: The outer diameter of
the Mounting Nut may need
to be dremeled down if space
under the counter is tight.
NOTE: Make sure Fiber
Optic Cables and Tubing are
INSIDE Mounting Nut. Do not
tighten completely until end of
installation.
5. Attach the tubing to
the top barb of the
Duckbill Housing.
6. The Bottle Cap can only
be placed onto the Stem
in one orientation.
The flat section on the
Stem is to be aligned with
the flat section on the
Bottle Cap.
7. Rotate the Bottle back
and forth to align the flat
section of the Stem to the
flat section on the Bottle.
8. Push the Bottle Assembly
up onto the Stem while
also inserting the Duckbill
Housing into the hole
in the post on the Bottle
Cap.
Fully insert the Bottle
Assembly over the Stem
until it stops. Both red
o-rings must be inside the
Bottle Cap.
9. While pushing upwards
on the Bottle, Thread
the Stem Locking Nut
down onto the Bottle
Cap threads.
NOTE: After assembly, hold
the Stem and lightly rotate
the Bottle back and forth
and tug down to be sure it is
on tight. If it is loose, repeat
Steps 7 and 8.
NOTE: Tug Tubing on
Duckbill Housing down
from under the counter to
straighten out the tubing.
10. Insert Fiber Optic
Connector Tip into
Bottom Housing. Keyed
feature on Connector
Tip ensures Fiber Optic
Cables are always
located correctly.
11. Thread Fiber Optic Nut
onto Connector Port and
tighten completely.
15. Plug Power Supply into
Bottom Housing base.
Installation:
Filling Instructions: (use liquid soap only)
Unit will dispense Bulk Liquid Soap within a viscosity range of 100 to 19,000 cP.
1. Insert tip of BobKey provided into opening of concealed locking mechanism to disengage door.
2. Door will disengage and rotate clockwise for filling from the top.
3. Fill dispenser with commercially marketed bulk liquid hand soap
(Do not use foam liquid or lotion soap).
4. Close door counter-clockwise to lock in place.
Replacement Parts List
Part Name
Part No.
- A/C Adapter
3974-57
- International AC Adapter Plug Kit (U. K., Europe, Australia)
3974-55
- Mack Gasket Kit
824-167
(To secure Top Assembly under the counter due to irregular counter surface)
- External A/C Multi Adapter Kit
824-201
- Nozzle Tip Replacement Kit Liquid
824-210
- Duckbill Housing
824-322
- Installation Hardware Packet
824-443
(Includes Wave Washer, Counter Gasket, Mounting Nut, BobKey, Stem Mounting nut)
Part Name
Part No.
- Top Housing Assembly Liquid, Polished Brass
850-225
- Top Housing Assembly Liquid, Matte Black
852-225
- Top Housing Assembly Liquid, Brushed Nickel
855-225
- Top Housing Assembly Liquid, Polished Nickel
856-225
- Top Housing Assembly Liquid, Polished Chrome
858-225
(Top Housing Assemblies include Installation Hardware Packet and Duckbill Housing)
- Bottom Housing Assembly Liquid
858-250
TOP FILL ONLY !
4. Thread the Stem Locking
Nut onto the Stem. The
ribs on the Nut are to be
towards the top. Once
it goes past the two
red o-rings, the nut will
automatically stop
threading.
13. Align the Top Assembly
above the counter to
the desired position
and tighten the Mounting
Nut against the bottom
of counter so the Top
Assembly does not
easily rotate. Make sure
Fiber Optic Cables are
not between the
underside of the counter
and top of Mounting Nut.
See Steps 3 and 4.
Apply a bead of Silicone
around the base of the
Top Housing to prevent
spilled soap from going
through the mounting
hole.
12. Place Fiber Optic cable
cover over loose fiber
optics to conceal.
NOTE: DO NOT bend or
kink Fiber Optic Cables.
14. Place US plug into AC
Adapter and slide down
until it clicks into place.
For international
installations use
appropriate adapter
from 3974-55.
3
2
