INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
Bobrick ConturaSeries
®
Model B-4112 Surface-Mounted Soap Dispenser
2. cut plastic tabs off rear of soap valve face flush with indicated surface (see Figure 4).
3. Move flat rubber washer back to its initial position. Make sure flat edge of washer is even with the top of valve face.
4. hold the collar nut with the 1" (25mm) closed-end wrench. Make sure the notch in the collar nut is facing toward the front of
the dispenser and position nut behind soap valve hole inside dispenser.
5. screw new soap valve into collar nut, clockwise, until rear of valve face hits the front of the soap container.
6. push the soap valve into the rectangular recess in the face of the soap container with spout facing downward.
7. Tighten collar nut with wrench until tight enough so that valve will not leak around seal at front of unit.
8. install soap dispenser on wall bracket.
B. On Units With Notched Soap Valve Hole In Container
1. hold the collar nut with the 1" (25mm) closed-end wrench. Make sure the notch in the collar nut is facing toward the front of
the dispenser and position nut behind soap valve hole inside dispenser.
2. screw new soap valve into collar nut, clockwise, until rear of valve face hits the front of the soap container.
3. push the soap valve into the rectangular recess in the face of the soap container with spout facing downward.
4. Tighten collar nut with wrench until tight enough so that valve will not leak around seal at front of unit.
5. install soap dispenser on wall bracket.
Note: Should a refill-indicator window replacement be required, order part No. 4112-34.
VALVE REPLACEMENT INSTRUCTIONS
TO REMOVE VALVE:
1. open filler-top by inserting BobKey (24-17) into slot of filler-top and
then sliding latch to the left. Lift up filler-top.
2. Loosen locking-screw inside dispenser. remove dispenser from wall
and empty soap container.
3. place 1" (25mm) closed-end wrench (provided) inside soap container
and over the large collar nut at rear of soap valve and loosen until face
of valve can rotate.
4. while holding the collar nut in place with the wrench, unscrew soap
valve from the front of the unit by rotating counterclockwise.
TO INSTALL VALVE:
A. On Units With Round Hole In Soap Container
1. pull back flat rubber washer at rear of soap valve face to expose the
two plastic tabs.
REPLACEMENT PARTS LIST
Part Name
Part No.
BobKey
24-17
collar Nut for Valve
4112-19
wall plate Assembly
4112-23
(wall plate, screws, BobKey)
window replacement Kit
4112-34
Aluminum wrench
4112-41
Locking-screw
4112-73
Valve replacement Kit
4112-79
(Round Hole Units Only)
Plastic Tabs To Be Cut Off
Flat With This Surface
Plastic Tab (2)
Flat Rubber Washer
Moved Back To Expose
Plastic Tabs
Collar Nut
4112-19
Valve
Replacement Kit
4112-79
Collar Nut
for Valve
4112-19
BobKey
24-17
Mounting Screw
(3 Required)
Wall Plate
Assembly
(Wall Plate, screws,
and BobKey)
4112-23
Locking Screw
Washer for Locking Screw
Soap Container
Window
Replacement Kit
4112-34
Wall Plate
FIgURE 4
FIgURE 5
7
16954 00231
0
B-4112
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, New York 12065-1350 • Tel: (518) 877-7444 • FAX: 518-877-5029
11611 Hart Street, North Hollywood, California 91605-5882 • Tel: (818) 982-9600 • FAX: 818-503-1102
100 Bobrick Drive, Jackson, Tennessee 38301-5625 • Tel: (731) 424-7000 • FAX: 731-424-7800
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Tel: (416) 298-1611 • FAX: 416-298-6351
© 2008 by Bobrick washroom equipment, inc.
Form No. 4112-269
revised 12/08 printed in U.s.A.