REPLACEMENT PARTS LIST
Part Name
Part No.
Valve Replacement Kit
4112-79
Collar Nut for Valve
4112-19
Window with O-Ring
2112-34
BobKey
24-17
VALVE REPLACEMENT INSTRUCTIONS
TO REMOVE VALVE:
1. Open filler-top by inserting BobKey (24-17) into slot of filler-top and then sliding latch to the left. Lift up filler-top.
2. Loosen locking-screw inside dispenser. Remove dispenser from wall and empty soap container.
3. Place 1" (25mm) closed-end wrench (provided) inside soap container and over the large collar nut at rear of soap valve and loosen until
face of valve can rotate.
4. While holding the collar nut in place with the wrench, unscrew soap valve from the front of
the unit by rotating counterclockwise.
TO INSTALL VALVE:
A. ON UNITS WITH ROUND HOLE IN SOAP CONTAINER
1. Pull back flat rubber washer at rear of soap valve face to expose the two plastic tabs.
2. Cut plastic tabs off rear of soap valve face flush with indicated surface (see Figure 4).
3. Move flat rubber washer back to its initial position. Make sure flat edge of washer is
even with the top of valve face.
4. Hold the collar nut with the 1" (25mm) closed-end wrench. Make sure the notch in the
collar nut is facing toward the front of the dispenser and position nut behind soap valve hole inside dispenser.
5. Screw new soap valve into collar nut, clockwise, until rear of valve face hits the front of the soap container. Adjust so that spout faces
downward.
6. Tighten collar nut with wrench until tight enough so that valve will not leak around seal at front of unit.
7. Install soap dispenser on wall bracket.
B. ON UNITS WITH NOTCHED SOAP VALVE HOLE IN CONTAINER
1. Hold the collar nut with the 1" (25mm) closed-end wrench. Make sure the notch in the collar nut is facing toward the front of the
dispenser and position nut behind soap valve hole inside dispenser.
2. Screw new soap valve into collar nut, clockwise, until rear of valve face hits the front of the soap container.
3. Push the soap valve into the soap container with valve tabs in the soap valve hole notches with spout facing downward.
4. Tighten collar nut with wrench until tight enough so that valve will not leak around seal at front of unit.
5. Install soap dispenser on wall bracket.
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
Bobrick Classic™ Series Models B-2111 and B-2112 Surface-Mounted Soap Dispensers
3OAP#ONTAINER
3OAP6ALVE
#OLLAR.UT
7ALL0LATE
3CREW
7INDOW
WITH/2ING
"OB+EY
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, New York 12065-1350 • Tel: (518) 877-7444 • FAX: 518-877-5029
11611 Hart Street, North Hollywood, California 91605-5882 • Tel: (818) 982-9600 • FAX: 818-503-1102
100 Bobrick Drive, Jackson, Tennessee 38301-5625 • Tel: (731) 424-7000 • FAX: 731-424-7800
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Tel: (416) 298-1611 • FAX: 416-298-6351
© 2005 by Bobrick Washroom Equipment, Inc.
Form No. 2112-269
Revised 6/05
Printed in U.S.A.
FIGURE 4
0LASTIC4ABS
TOBE#UT/FF
&LUSHWITHTHIS3URFACE
0LASTIC4AB
&LAT2UBBER7ASHER
MOVEDBACKTO
EXPOSEPLASTICTABS
WWW.BOBRICK.COM
BobKey
