background image

2

EN

WARNING: 

Read the ENTIRE instruction manual to become familiar with the features of the product before operating. 

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. 

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic 
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage 
to the product or other property. This product is not intended for use by children without direct adult supervision. Do 
not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon 
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow 
all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid 
damage or serious injury.

The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:

WARNING:

 Procedures, which if not properly followed, create the probability of property damage, collateral damage, 

and serious injury OR create a high probability of superfi cial injury.

CAUTION:

 Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE:

 Procedures, which if not properly followed, create a possibility of physical property damage AND a little or 

no possibility of injury.

• Always keep a safe distance in all directions around 

your model to avoid collisions or injury. This model is 
controlled by a radio signal subject to interference from 
many sources outside your control. Interference can 
cause momentary loss of control.

• Always operate your model in open spaces away from 

full-size vehicles, traffi c and people.

• Always carefully follow the directions and warnings for 

this and any optional support equipment 
(chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything 

electrical out of the reach of children.

• Always avoid water exposure to all equipment not 

specifi cally designed and protected for this purpose. 
Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it 

could cause serious injury or even death.

• Never operate your model with low transmitter 

batteries.

• Always keep aircraft in sight and under control.
• Always move the throttle fully down at rotor strike.
• Always use fully charged batteries.
• Always keep transmitter powered on while aircraft is 

powered.

• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

Safety Precautions and Warnings

Age Recommendation: Not for children under 14 years. This is not a toy. 

NOTICE

Meaning of Special Language

Summary of Contents for Blade mCP


















Reviews: