Thank you for purchasing a BN Thermic product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
1. S A F ET Y I N ST R U C T I O N S
1 . 1 ELECTRICAL SAFETY
❑
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, socke ts and any
other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. If in any doubt consult a qualified
electrician. You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the
safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.2 Ensure that the insulation of all the cables on the appliance is safe before connecting it to the power supply.
1.1.3 Ensure that the cables are always protected against short circuit and overload.
1.1.4 Regularly inspect the power supply cables and plugs etc. for wear or damage and check all connections to ensure that none are loose.
1.1.5 Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that a correctly rated fuse is fitted.
1.1.6 Installation should always be carried out by a qualified electrician in accordance with current electrical regulation, protected by a suitably rated
isolator and fuse or mcb.
1.1.7 DO NOT use worn or damaged cables or connectors. Immediately have any faulty item repaired or replaced by a qualified electrician.
1.1.8 If the supply cord is damaged, it must be replaced by the manufacturer or
it’s service agent.
1.19
Do not use in hazardous areas.
1.2 GENERAL SAFETY INSTRUCTIONS
✓
Remove all packaging and store it away from children, check the package and heater for visible damage or tampering.
✓
Familiarise yourself with the applications and limi tations of the heater.
✓
Ensure the heater is in good order and condition both physically and electrically before use. If in any doubt do not use the unit and
contact your supplier.
✓
Disconnect from mains and allow to cool before attempting any cleaning.
X
DO NOT
use in hazardous areas.
X
DO NOT
use if ambient temperatures exceed 30°C.
X
DO NOT
cover the heater or restrict free circulation of air around it.
X
DO NOT
locate the heater below the power outlet.
X
DO NOT
install this heater against combustible low-density fibre board surfaces.
X
DO NOT
disassemble the heater for any reason. This heater must be checked by
qualified personnel only.
X
DO NOT
use this heater to perform a task for which it has not been designed.
❑
WARNING!
This heater is not equipped with a device to control the room temperature.
Do not use this heater in a small room if it is occupied by people not capable of leaving
the room on their own, unless constant supervision is provided.
❑
WARNING!
Ensure there is no possibility of inflammable materials coming into
contact with the heater.
2 . IN T R O D U C T I O N & S P E C I F IC A T I O N
RP3 Ceiling Panels are designed to provide primary, localised or perimeter heating. The heaters
should be ceiling mounted ideally between 2.4m and 3.5m from floor level. RP3 Ceiling Panels are
a more economic means of heating commercial premises than conventional heating systems
because the gentle radiant effect felt from them
means that the ‘experienced temperature’ can be
up to 4°C warmer than the actual air temperature. This means that the thermostat can be set up
to 4°C lower saving power and electricity costs. A suitable air sensing thermostat and timer should
be used.
Model
RP3-03
RP3-06
Power
300W
600W
Input supply
230V 50Hz 1.3A
230V 50Hz 2.6A
Dimensions (W x H x D)
592 x 592 x 30mm
1192 x 592 x 30mm
Weight
5.9Kg
11.3Kg
Minimum Mounting Height
1.8M
1.8M
Recommended Mounting Height
2.4
– 3.5M
2.4
– 3.5M
IP rating
IP44
IP44
INSTRUCTIONS FOR:-
RADIANT CEILING PANELS
RP3 Series
IMPORTAN
T: PLEASE READ THESE INSTRUCTIONS, NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO
DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
REGISTER
: PLEASE REGISTER THIS PRODUCT ONLINE TO ACTIVATE YOUR GUARANTEE AT
www.
bnthermic
.co.uk
