manualshive.com logo in svg

BMW Z4, Owner'S Manual

Introducing the True Z4 - the ultimate fitness companion. Unlock the full potential of your workout routine with our cutting-edge features and advanced technologies. Access the comprehensive Owner's Manual and unleash your fitness journey today. Download your free manual exclusively at manualshive.com and embark on a transformative fitness experience.

Share
Download
background image

of the spine. The lower back and the spine are
supported for upright posture.

Adjusting

▷

Press the front/rear section of
the button:
The curvature is increased/
decreased.

▷

Press the upper/lower section
of the button:
The curvature is shifted up/
down.

Backrest width

Concept

Adjusting the backrest width may improve lateral
support when taking corners.

General information

You can change the backrest width by adjusting
the side wings of the backrest.
To make it easier to enter and exit the vehicle,
the backrest width temporarily opens fully.

Adjusting

▷

Press the front section of the
button:
The backrest width de‐
creases.

▷

Press the rear section of the
button:
The backrest width increases.

Safety belts

Number of safety belts and

safety belt buckles

The vehicle is fitted with two safety belts to en‐
sure occupant safety. However, they can only of‐
fer protection when adjusted correctly.

General information

Always make sure that safety belts are being
worn by the occupants before driving off. The
airbags supplement the safety belts as an addi‐
tional safety device. The airbags are not a substi‐
tute for safety belts.
The upper shoulder strap's anchorage point will
be correct for adult seat occupants of every build
if the seat is correctly adjusted.

Safety information

Warning

Use of a safety belt to buckle more than one
person will potentially defeat the ability of the
safety belt to serve its protective function.
There is a risk of injuries or danger to life. Do
not allow more than one person to wear a sin‐
gle safety belt. Infants and children are not al‐
lowed on an occupant's lap, but must be trans‐
ported and secured in designated child
restraint systems.

Warning

The efficacy of safety gear, including safety
belts, can be limited or lost when safety belts
are fastened incorrectly. An incorrectly fastened
safety belt can cause additional injuries, for in‐
stance in the event of an accident or during
braking and evasive maneuvers. There is a risk
of injuries or danger to life. Make sure that all
occupants are wearing safety belts correctly.

Seite 102

CONTROLS

Seats, mirrors, and steering wheel

102

Online Edition for Part no. 01402779113 - II/19

Summary of Contents for Z4











































































































































































































































































































































Reviews:

No comments

Related manuals for Z4

Accel 2020 Installation Instructions preview
2020
Brand: Accel Pages: 2
Hama Pico Operating Instructions preview
Pico
Brand: Hama Pages: 2
MASCOT SMARTCHARGER User Manual preview
SMARTCHARGER
Brand: MASCOT Pages: 12
Quadratec 12226.3011 Installation Manual preview
12226.3011
Brand: Quadratec Pages: 8
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Brand: Sumitomo Pages: 22
Mitsubishi MIrage 2019 Owner'S Handbook Manual preview
MIrage 2019
Brand: Mitsubishi Pages: 19
Thule PORTAGE 819 Instructions Manual preview
PORTAGE 819
Brand: Thule Pages: 12
Veldo Teknoloji DUCATO Manual preview
DUCATO
Brand: Veldo Teknoloji Pages: 32
Renault Laguna III Manual preview
Laguna III
Brand: Renault Pages: 3699
Roadmaster Even Brake 9400 Owner'S Manual preview
Even Brake 9400
Brand: Roadmaster Pages: 20
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9
A-Tach Mounts 50321 Quick Start Manual preview
50321
Brand: A-Tach Mounts Pages: 2
Thule 2087 Parts List preview
2087
Brand: Thule Pages: 1
Haltech Platinum Pro Plug-in Quick Start Manual preview
Platinum Pro Plug-in
Brand: Haltech Pages: 20
Safe Fleet HD3S Quick Installation Manual preview
HD3S
Brand: Safe Fleet Pages: 2
Scion 2015 FR-S Quick Reference Manual preview
2015 FR-S
Brand: Scion Pages: 24
Kia FORTE Manual preview
FORTE
Brand: Kia Pages: 38
Lotus ELISE 2007 Owner'S Handbook Manual preview
ELISE 2007
Brand: Lotus Pages: 200

Brands by name

Popular brands

Load more brands