manualshive.com logo in svg

BMW R 1100 GS + Adventure, Repair Manual

Share
Download
BMW R 1100 GS + Adventure Repair Manual Download Page 246

31.8

[RS] Removing and installing fork 
bridge

•

Separate connecting plug for ignition/steering 
lock. 

•

Unscrew handlebar mount on fork bridge.

•

Remove trim (1).

•

Heat ball joint mount on fork bridge to max. 
120 °C and unscrew using Allen key socket 
wrench insert, 

BMW No. 31 5 600

.

•

Unscrew fixed tube clamp mount at top of fork 
bridge.

•

Remove fork bridge.

•

Remove ignition/steering lock.

•

Install in the reverse order of work.

Projection of fixed tube beyond fork bridge:

................................ 5 

± 0.5

 mm (0.1969

± 0.01969 

in)

X

 Tightening torque:

Mount, fixed tube/fork bridge ....................... 22 Nm
Ball joint at fork bridge 
(clean  Loctite 2701)...................... 130 Nm

[GS/R/RT] Removing and installing 
fork bridge

•

Unscrew fuel tank and pull to the rear.

•

Separate connecting plug for ignition/steering 
lock. 

•

Detach handlebar from fork bridge.

•

Unfasten fixed tube screw connection at fork 
bridge, preventing movement by holding hexa-
gon on fixed tube.

•

Unfasten screw connection between fork bridge 
and frame.

L

 Note:

Screw pin is a press fit in ball thrust bearing: remove 
complete unit.

•

[R] 

Scheinwerferhalterung nach vorne ziehen.

•

Gabelbrücke abnehmen.

•

Zündlenkschloß ausbauen.

•

Einbau in umgekehrter Reihenfolge.

X

 Tightening torque:

Screw connection between fork bridge and frame
(clean  Loctite 243)........................ 130 Nm
Threaded connection between fork bridge and fixed 
tube (free from oil and grease)...................... 45 Nm
Handlebar to fork bridge .............................. 21 Nm

GS310030

31 5 600

1

j

120

w

GS000410

Summary of Contents for R 1100 GS + Adventure

















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands