manualshive.com logo in svg

BMW Motorrad S 1000R 2017, Rider'S Manual

Share
Download
BMW Motorrad S 1000R 2017 Rider'S Manual Download Page 164

Disconnecting battery
from motorcycle

Place the motorcycle on its
stand on firm, even ground.
Switch off the ignition.
Removing front seat (

60).

ATTENTION

Battery not disconnected in
accordance with correct pro-
cedure

Risk of short-circuit

Always proceed in compliance
with the specified disconnec-
tion sequence.

Remove the battery earth
lead

2

. Also remove the

washer between the battery
and the battery earth lead.
Remove positive battery
cable

1

.

Connecting battery to
motorcycle

Connect battery positive lead

1

first.
Replace the washer between
the battery and the battery
earth lead. Then install bat-
tery negative lead

2

.

Installing front seat (

61).

Recharging battery

Disconnecting battery from
motorcycle (

162).

Charge the battery using a
suitable charger.
Comply with the operating in-
structions of the charger.
Once the battery is fully
charged, disconnect the
charger's terminal clips from
the battery terminals.

NOTICE

The battery has to be recharged
at regular intervals in the course
of a lengthy period of disuse.
See the instructions for caring
for your battery. Always fully re-
charge the battery before restor-
ing it to use.

Connecting battery to motor-
cycle (

162).

9

162

z

Maintenance

Summary of Contents for S 1000R 2017



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands