bluwash BWD2000 Instruction Manual Download Page 3

BWD2000

(1) General Features

Do not hang heavy stuffs on the power cable or give a pull on it. 

Also do not get it damaged, bend it by force, or twist it. If you do so, 

Check and clean the machine regularly so that dust is not stacked 

up on the interior of the machine and the power cable part.
This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.
children should be supervised to ensure that they do not play with the

appliance. 

This machine is sanitary as you can use it without touching any instrument or 

switch by automatic coming-out of warm wind right after putting your hands into 

the air vent. 
To prevent children's mischief or continuous running by the sensing error of the sensor, 

the machine is designed to be stopped about 20 seconds after continuous running. 

You can reuse it by pull the hands out and then put them in again.
The built-in water receiver is removable slide, therefore anyone can easily remove the 

water that is full in the receiver.

Do not lean on or hang on the machine - You may be possibly injured 

with the separation of the machine.
Do not use the machine other than drying hands (Ex: Drying hair) - You 

may be possibly injured or burned with bumping against the machine.
Do not put a towel or other stuffs on the machine - Fire may possibly 

occur or you may be injured with the falling stuff on the machine.
Do not use toilet detergent, house detergent, benzene, thinner, cleanser 

and nylon scrubber when you clean the machine because they can 

damage plastics.

2. Features of Product

If the supply cord is damaged, it must be replaced by the manufacturer, 

Warning

Caution

Summary of Contents for BWD2000
















Reviews: