background image

1

Accessories

Page 3 

Revised 5/14/2020

Accessories

The air conditioning system comes with the following accessories. Use all of the installation parts and 

accessories to install the air conditioner. Improper installation may result in water leakage, electrical 

shock and fire, or equipment failure.

Name

Name

Shape

Quantity

Remote Control

Remote controller (some models)

1

Batteries

AAA

2

Remote control

holder (some models)

Remote sheath

1

Screws for remote sheath

2

EMC Magnetic Ring

(some models)

Magnetic ring

(wrap the electric wires S1 & S2 ( P & Q & E )

around the magnetic ring twice)

1

Magnetic ring

(Hitch on the connective cable between the 

indoor unit and outdoor unit after installation.)

1

Others

Owner‘s manual

1

Installation manual

1

Refrigerant line adaptor - 1/2" to 5/8"  

NOTE: Pipe size may differ from appliance 

to appliance. Use the refrigerant adapter if 

needed always at the condenser.

1

(on some 

models)

Refrigerant line adaptor - 1/4" to 3/8"

NOTE: Pipe size may differ from appliance 

to appliance. Use the refrigerant adapter if 

needed always at the condenser.

1

(on some 

models)

Refrigerant line adaptor - 3/8" to 1/2"

NOTE: Pipe size may differ from appliance 

to appliance. Use the refrigerant adapter if 

needed always at the condenser.

1

(on some 

models)

Red short connected wire (Applied to the W/L 

pin of outdoor unit terminal block be short-

circuited.)

1

(on some 

models)

S1&S2(P&Q&E)

Summary of Contents for BM18MFCC

















Reviews: