1
2
SAFETY
Before use ensure the Bottle Jack is in good working order and not damaged. If the Bottle Jack
is damaged remove from service immediately. Damaged parts should be repaired or replaced
before the unit is used again. This should be undertaken using genuine parts by a trained
technician.
●
Ensure
the load is within the lifting capacity of the jack.
●
Ensure
the jack is used on level ground, preferably concrete. Avoid soft surfaces like
Tarmacadam as the jack may sink.
●
Ensure
all but essential personnel keep a safe distance while the jack is in use.
●
Ensure
the work area is well lit, clean and free from clutter.
●
Ensure
work area floor is sound and not slippery so a firm footing can be maintained.
●
Ensure
only competent personnel operate the hydraulic jack.
●
Ensure the area is clear before lowering the load
●
Ensure the lifting point is centred and stable on the jack saddle – to avoid loads slipping.
●
If using the jack on a Vehicle:-
●
Ensure
the vehicle weight is within capacity and that the recommended lifting points
are used – see owner’s manual. Position the Jack to avoid operating it from under the
vehicle.
●
Ensure jacking the vehicle will not result in a leakage of fuel or other dangerous fluids.
●
Ensure
wheel nuts are slightly loosened before jacking, and only lightly tightened
before lowering. Fully tighten the nuts to the specified torque when the car is on the
ground. This process avoids moving the vehicle while it is raised. Check wheel nut
torque again after a short journey.
●
Ensure
the hand brake is applied (in Park for Automatics), engine switched off and
chocks placed under the wheels.
●
Ensure
a minimum clearance of 0.5m between the vehicle and any other objects to
allow for raising and tilting during jacking.
●
Ensure
all occupants are out of the vehicle before lifting and never let anybody in the
vehicle while on the jack or axle stands.
●
Ensure
suitable axle stands, correctly positioned, are used to support the vehicle
before placing any part of your body under the vehicle.
DANGER –
Changing the wheel at the roadside is hazardous. Take extra care -avoid
jacking on Tarmac, traffic may cause the vehicle to rock, use hazard warning lights and
NEVER go under the vehicle. If in doubt seek professional help – especially with caravans
or trailers.
DANGER
Use the jack for lifting only – never to support the lifted load for other work tasks eg welding..
●
DO NOT
exceed the rated capacity Jack or exceed its maximum pump stroke.
●
DO NOT
allow untrained personnel to operate the Jack.
●
DO NOT
remove labels from the Jack – replace any damaged or unclear labels.
●
DO NOT
modify the Jack or use it for any purpose it was not intended for.
●
DO NOT
use when under the influence of drugs, alcohol or medication that may cause
drowsiness.
●
DO NOT
top the Jack up with Brake fluid. USE only the recommended hydraulic oil.
●
DO NOT
use the lever hoist if any chains are kinked or knotted.
BOTTLE JACK
IMPORTANT-CAUTION
Install, operate and maintain this equipment in accordance with these instructions. Failure to do so
may lead to personal injury, damage to the Jack and invalidation of the warranty.
Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that
all accessory lifting devices are suitably certified. If Jack is damaged, remove from service
immediately.
Read thoroughly the contents before use and keep this handbook for future use.
OPERATION
The Bottle Jack may have accumulated air during transit, to ensure this is eliminated by purging
the system as follows. Open the release valve (1) and pump the system several times. Close the
release valve (1) .
●
LIFTING
1.
Before operating estimate the weight of the load. Do not operate the jack
above its rated load.
2
. Identify the centre of gravity of your load and place the jack on hard
ground. A suitable solid pad may be used under the jack to avoid it sinking
or leaning in softer surfaces.
3.
Before operating the jack, insert the notched end of the handle into
the release valve (1).Turn the operating handle clock wise until the release
valve is closed. Do not over tighten the valve.
4
. Insert operating handle into the socket slowly pump until the saddle
touches the load. Ensure it seats properly with the load, then slowly
continue pumping until the load is at the required height. The ram will stop
rising when the maximum height is reached – do not try to over extend the
jack.
BOTTLE JACK
