bluelab ppm pen Care And Use Manual Download Page 8

Bluelab ppm Pen product guarantee

Bluelab Corporation Limited guarantees this product for a period of 

1 year

(12 months)

 from the date of sale to the original purchaser. The product

will be repaired or replaced, should it be found faulty due to component
failure, or faulty workmanship. The faulty product should be returned to
the point of purchase.

The guarantee is null and void should any internal parts or 

fi

 xed external parts

be tampered with or altered in any way, or should the unit have been incorrectly
operated, or in any way be maltreated. This guarantee does not cover reported faults which are shown 
to be caused by any or all of the following: contaminated measuring tip (see instruction manual 
for cleaning instructions), broken glassware or drying of the pH probe glassware, 

fl

 at or damaged 

batteries or batteries that have been incorrectly inserted, or damaged battery contacts or connections 
caused by incorrect battery replacement or ingress of moisture from incorrect positioning of the 
battery cap and waterproof seal.

NO RESPONSIBILITY will be accepted by Bluelab or any of its agents or resellers should any 
damage or unfavourable conditions result from the use of this product, should it be faulty or 
incorrectly operated.

Register your guarantee online at: www.getbluelab.com

Or fi ll out the form below and post, email or fax to:

Bluelab Corporation Limited
8 Whiore Avenue, Tauriko Industrial Park, Tauranga 3110, New Zealand

Fax:

 +64 7 578 0847        

Email

:  [email protected]  

Product details

Product name

Serial number

Date purchased

Purchaser details

Purchaser’s name

Address

City

Country

Email (optional)

Purchased from (Dealers details)

Purchased from

Address

City

Country

Phone number 

(optional)

1

year

 B

LU

EL

AB

 RE

PAIR OR REPLA

CE

M

EN

year

ea

ea

B

LUU

EELL

A

L

B

RE

PA

PP IR OR REPLAL

CCC

A

EEEMMM

EEEN

T

 P

R

OD

U CT GUARAN

TE

E

English

8

Summary of Contents for ppm pen










Reviews: