background image

LADDER ASSEMBLY INSTRUCTIONS

WARNING - 

VERY IMPORTANT

LADDER WEIGHT LIMIT IS 300 POUND

S

*  LOOSE HARDWARE WILL RESULT IN LADDER FAILURE.

*  The ladder will fail if the Machine Screws (45), Washers (46), Lock Washers (47),   

       and Cap Nuts (48) holding handles to legs are not properly installed.

TOOLS REQUIRED:

 

•  Phillips head screwdriver    •   Small adjustable wrench

1.   Separate the Ladder Legs (40) – 2 pieces each left and right. Look for the “L” and “R” 

on the top of the legs.

2.   Start with one “R” ladder leg section (40). Carefully  pry open one ladder step clip (44) 

from the side, just enough to get over the top section of the ladder leg, and slide it from 

the top of the leg down to the lowest indented section as shown in Figure 1. The ridge 

on the ladder clip should be on the inside of the leg as shown in Figure 2. Repeat with 

“L” leg section.

3.   Slide a step (42) down over both legs. Make sure that the side of the step marked with 

an “R” is on the right side leg. Slide the step down until the ladder step clips (44) in-

serts into the underside of the step and the ridges inside of the clips lock into place. The ladder step clips should stay in the 

indented section of the ladder leg as you press the steps down 

over them. The ladder step clips should insert flush against the 

bottom of the step. See Figure 2.

4.   Repeat Steps 2 and 3, installing the rest of the ladder step clips 

(44) and steps (42) for the first section. 

5.   Assemble the second ladder leg section in the same manner, 

repeating step 2-4.

6.   The Machine Screws (45) should be installed from the inside of 

the Handle (41), and out through the Ladder Handle Brace with 

Safety Label (49) on the outside.  Make sure that the English 

warning label is facing out on both handle sections. Install the 

Lock Washer (47), and thread the Cap Nut (48) on until the Lad-

der Brace tightens up against the Handle.

7.   Stand both ladder leg sections in the upright position, with feet 

facing outward, as shown in Figure 3.  Place the ladder handles 

(41), with the ladder handle braces on the outside of the ladder, 

on top of both ladder leg sections.

8.   Make sure all of the steps are now level (parallel to the ground) 

and that the Safety Warning Labels are facing outward in the 

right direction as in # 6 above. 

9.   From the inside of the ladder handles, insert the four machine screws (45) through the flat washers (46), then through the 

handle and fasten in place using the four lock washers (47) and cap nuts (48).  See Figure 4.

NOTE:  THIS STEP IS VERY IMPORTANT BECAUSE IT KEEPS THE HANDLES FROM SEPARATING FROM THE 

LEGS - LADDER FAILURE WILL RESULT IF SCREWS ARE NOT PROPERLY INSTALLED!

MAINTENANCE:

 1.  Keep ladder steps cleared off and free of mud, which causes slipping.

 

 

          2.  Retighten ladder hardware periodically; LOOSE HARDWARE WILL CAUSE LADDER FAILURE.

                               

1.  Locate ladder on a solid base, use the pool ladder as the only means of entering  

   

 

 

     and exiting pool.

LADDER SAFETY 

2.  ONE PERSON ON THE LADDER/STAIR AT A TIME, instruct everyone                                                                                            

                                            not to swing, rock, jump, or dive from ladder.

     

 

 

3.  FOR ENTRY / EXIT OF POOL, FACE THE LADDER AT ALL TIMES.

     

 

 

4.  VERY IMPORTANT: REMOVE AND SECURE LADDER WHEN POOL  IS  

   

 

 

     NOT OCCUPIED; Help save a life by preventing unauthorized access to Pool.

     

 

 

5.  Ladder shall be assembled and installed per manufacturer’s instruction.

                         

     

 

 

6.  To reduce the risk of injury or death, do not permit children to use this        

   

 

 

     product unless they are closely supervised at all times.

                                          7.  During nighttime pool use, artificial lighting shall be used to illuminate all

                                               safety signs, ladders, steps, deck surfaces and walks.

THIS LADDER IS DESIGNED AND MANUFACTURED FOR THE SPECIFIC POOL  

WALL HEIGHT AND OR DECK OF THE POOL .                                                        

 REMOVE AND SECURE LADDER WHEN POOL IS NOT OCCUPIED!

POOL LADDER PARTS LIST

KEY

DESCRIPTION

3 FT. 

POOL 

WALL 

HEIGHT

3.5 FT. 

POOL 

WALL 

HEIGHT

4 FT. 

POOL 

WALL 

HEIGHT

52” 

POOL 

WALL 

HEIGHT

40

Ladder Legs

4

4

4

4

41

Ladder Handles

2

2

2

2

42

Ladder Steps

6

6

8

8

43

Leg End Caps

4

4

4

4

44

Ladder Step Clips

12

12

16

16

45

Machine Screws

8

8

8

8

46

Washers

4

4

4

8

47

Locking Washers

8

8

8

8

48

Cap Nuts

8

8

8

8

49

Ladder Brace w/ Safety Label

2

2

2

2

50

Anti-Entrapment Barrier

1

1

1

1

51

Lock Pin

1

1

1

1

!

WARNING:

084-120155

Reviews: