Blue Seal Turbofan E32M Service Manual Download Page 38 | Manualshive

Page: 38 / 48

Blue Seal Turbofan E32M Service Manual Download Page 38

-38-

Revision 1/F3586

9. SPARE PARTS

Controls

     021473     Power Switch
     024774     Thermostat
     021472     Knob - Thermostat
     020849     Neon Indicator
     011760     Bake Timer
     011794     Buzzer
     021476     Switch- Roast ’n’ Hold
     011419       Roast ’n’ Hold Timer
     020823     Knob - Bake Timer / Roast ’n’ Hold Timer
     021474     Steam Switch
     024773     Light Switch
     015966     Contactor - Elements
     021491     Relay - Roast ’n’ Hold
     018223     Hold Thermostat
     024802     Microswitch
     003002     Oven Lamp Glass
     003434     Silk Gasket
     013521     Oven Lamp - 40W Miniature Edison Screw

Motor & Elements

     015360     Element Assembly 208-220V
     015363     Element Assembly 230-240V
     024431     Fan Motor
     024432     Capacitor 3uF
     024503     Motor Timer 208-220V
     024567     Motor Timer 220-240V
     024433     Fan

Steam System

     020851     Water Solenoid
     021057     Spray Nozzle Assembly
     021526     Water Inlet Elbow
     021527     Washer

Door

     024784     Door Seal (Side)
     024785     Door Seal (Top/Bottom)
     020082     Top Hinge
     020083     Bottom Hinge
     024809     Roller Catch
     017905     Door Bush

     021468     Door Handle (E32M)
     024599     Door Handle Bracket (E32M)
     024844     Door Outer Glass (E32M)
     002340     Door Inner Glass (E32M)

024713 Door Handle (E32MS)
023063 Door Glass (E32MS)

Racks

     015575     Oven Side Rack LH
     015656     Fan Baffle
     015168     Oven Rack

Stacking Kit

021543 Double Stacking Kit

«
...
36
37
38
39
40
...
»

Summary of Contents for Turbofan E32M

















































Reviews:

No comments