3
28
5
10
13
TX
30
TX
20
TX
40
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(9)
(10)
(10)
(11)
(12)
(13)
3
8
TX20
EN ASSEMBLY
INSTRUCTIONS
TOOLS REQUIRED
(1)
ratchet spanner with cap 13
(2) tape
measure
(3) pencil
(4)
bit torx TX20
(5)
bit torx TX30
(6)
bit torx TX40
(7)
drill and/or screwdriver
(8) square
(9)
wood bore bits Ø 3 and Ø 5 mm
(10)
speed bore bits Ø 10 and Ø 28 mm
(11)
wood saw
(12)
hammer
(13) sandpaper
WOOD SCREWS
step 1/ To prevent the wood spli ng we recommend pre-drilling all wood to be
screwed. Always drill at least 15 mm less deep than the length of the screw. Pre-
drill wood screws with a diameter of 4.5 mm with a 3 mm wood bore bit.
step 2/ First turn the screw one or two millimetres into the plank to be secured,
then press this
fi
rmly against the other piece of wood.
step 3/ Tighten the screw with the torx TX20 bit supplied in the wood un l the
head of the screw is level with the surface of the wood.
COACH SCREWS
step 1/ To prevent the wood spli ng we recommend pre-drilling all wood to be
screwed. Always drill at least 15 mm less deep than the length of the screw.
Pre-drill coach screws with a diameter of 8 mm with a 5 mm wood bore bit.
step 2/ Place the
fl
at washer and the bo om of the protec ve cap over the sha
of the screw.
step 3/ First turn the screw one or two millimetres into the beam to be secured,
then press this
fi
rmly against the other piece of wood.
step 4/ Tighten the screw with the torx bit TX40 supplied.
step 5/ Press the top of the protec ve cap into the opening provided.
BOLTED CONNECTIONS
step 1/ Drill a hole with diameter 10 mm through both planks or beams that have
already been screwed together (see ‘wood screws’)
step 2/ Hit the drive-in nut with a hammer along the designated side of the beam
in the hole.
step 3/ Place the spring ring, the
fl
at washer and then the bo om part of the
protec ve cap over the sha of the bolt.
step 4/ Push the bolt through the hole, and turn by hand several mes un l the
bolt turns smoothly in the press-in nut.
step 5/ Tighten the bolt with torx bit TX40 supplied, un l the spring ring is fully
fl
a ened between the head of the bolt and the
fl
at washer.
step 6/ Press the top of the protec ve cap into the opening provided.
5
TX
40
10
TX
40
Summary of Contents for Beach Hut
