13
English
EN
4
GENERAL INFORMATION (FIG.1)/PAGE 3
4.1 Use of the manual
The manual forms an integral part of the machine and should be
kept for future reference. Please read it carefully before installing/
using the machine. If the machine is sold, the seller must pass on
this manual to the new owner along with the machine.
4.2 Delivery
The machine is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
4.2.1
Documentation supplied with the machine
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
A4 Warranty regulations
4.3 Disposing of packaging
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
5
TECHNICAL INFORMATION (FIG.1)/PAGE 3
5.1 Intended use
The machine is intended for personal use for cleaning vehicles,
machinery, boats, masonry, etc., for removing stubborn dirt with
clean water and biodegradable chemical detergents, and as a
sprayer for aqueous solutions.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Inlet water temperature: see machine data plate.
- Inlet water pressure: min. 0.1 MPa - max. 1 MPa.
- Operating ambient temperature: above 0 °C.
The machine is compliant with the IEC 60335-1 and IEC 60335-2-79
standards.
5.2 Operator
The symbol in fig.1 identifies the machine’s intended operator
(professional or non-professional).
5.3 Main components
B2 Lance
B3 Trigger gun with safety catch
B4 Power cable with plug
B5 High pressure hose
B6 Solution tank
E Nozzle
L
Water filter
N Sprayer control lever
5.3.1 Accessories (where supplied - see fig.1)
C1
Nozzle cleaning tool
C2
Rotary nozzle kit
C3
Handle
C4
Brush
C5
Hose reel
C6
Water suction kit
C7
Drain pipe cleaning kit
C8
Large surface brush kit
C9
Adaptor
C10
Screws
C11
Brackets
C12
Lever
C13
Detergent kit
C14
Wheels
P1
Grip
P2
Lance
P3
Delivery hose
P4
Sprayer nozzle
P5
Trigger gun filter
P6
Tank filter
P7
Lever catch
5.4 Safety devices
- Starter device (H)
The starter device prevents accidental use of the machine.
Warning - danger!
Do not tamper with or adjust the safety valve setting.
- Safety and/or relief valve.
The safety valve is also a relief valve. When the gun trigger is
released, the valve opens and the water recirculates through the
pump inlet or is discharged onto the ground.
- Safety catch (D): prevents accidental spraying of water.
- Overload cutout: stops the machine in case of overload.
6
INSTALLATION (FIG.2)/PAGE 4
6.1 Assembly
Warning - danger!
All installation and assembly operations must be
performed with the machine disconnected from the mains
power supply.
The assembly sequence is illustrated in fig.2.
6.2 Assembling the rotary nozzle
(For models with this feature).
The rotary nozzle kit delivers greater washing power.
Use of the rotary nozzle may cause a reduction in pressure of 25%
compared to the pressure obtained with the adjustable spray
nozzle. However, the rotary nozzle delivers greater washing power
due to the rotation of the water jet.
6.3 Electrical connection
Warning - danger!
Check that the electrical supply voltage and frequency
(V-Hz) correspond to those specified on the data plate (fig.2).
6.3.1
Use of extension cables
The cross-section of the extension cable should be
proportionate to its length; the longer it is, the greater its
cross-section should be. See table I.
6.4 Water supply connection (high pressure washer function)
Warning - danger!
Only clean or filtered water should be supplied to the
machine. The flow rate of the water inlet tap must be equal
to that of the pump.
Place the machine as close to the water supply system as possible.
6.4.1
Connection points
l
Water outlet (OUTLET)
n
Water inlet with filter (INLET)
6.4.2
Connection to the mains water supply
The machine may only be connected directly to the
mains drinking water supply if the supply hose is fitted
with a backflow preventer valve with drain facility as per
current regulations in force. Make sure that the hose is at
least Ø 13 mm, that it is reinforced and that it is not more
than 25 m long.
6.4.3
Sucking in water from open tanks
1) Screw the suction hose with filter to the water inlet
(INLET) and insert it down to the bottom of the tank.
2) Vent the air from the machine:
a) Unscrew the lance.
b) Start the machine and keep the trigger gun open until
there are no air bubbles in the water flowing out.
3) Switch the machine off and screw the lance back on.
N.B.: the maximum suction height is 0.5 m. The suction
hose should be filled before use.
7
ADJUSTMENTS (FIG.3)/PAGE 5
7.1 Adjusting the nozzle (for models with this feature)
The water jet is adjusted by regulating the nozzle (E).
8
INFORMATION ON USE OF THE MACHINE (FIG.4)/PAGE 6
Warning - danger!
Ensure that the machine is standing on a firm, solid
surface. The machine must be used in the upright position.
Do not cover the machine or use it in locations with poor
ventilation.
