background image

PRECAUTIONS AND GENERAL INFORMATION 

WARNING:  

ELECTRIC SHOCK HAZARD 

All servicing requiring access to non-insulated components must be performed by qualified 
service personnel.  Do not open any access panels which require the use of tools. 

              Failure to heed this warning can result in electrical shock. 

 

WARNING:  

INJURY HAZARD 

All installation procedures must be performed by qualified personnel with full knowledge of all 
applicable electrical and plumbing codes.  Failure could result in property damage and 
personal injury. 

 

WARNING:  

ELECTRIC SHOCK HAZARD 

Brewer must be properly grounded to prevent possible shock hazard.  DO NOT assume a 
plumbing line will provide such a ground.  Electrical shock will cause death or serious Injury. 

 

WARNING:  

BURN HAZARD 

This appliance dispenses very hot liquid.  Serious bodily injury from scalding can occur from 
contact with dispensed liquids. 

This appliance is intended for commercial use only. 

 
This appliance is intended for use to brew beverage products for 
human consumption.  No other use is recommended or  
authorized by the manufacturer or its agents. 

 
This appliance is intended for use in commercial establishments, 
where all operators are familiar with the appliance use,  
limitations and associated hazards.  Operating instructions and 
warnings must be read and understood by all operators and  
users. 

 

 
The following trouble shooting, component views and parts lists 
are included for general reference, and are intended for use by 
qualified service personnel. 

 
This manual should be considered a permanent part of this 
appliance.  The manual must remain with the appliance if it is 
sold or moved to another location. 
 
 
 
 
 
 
This brewer is         and           listed under UL file E9253. 
 
 
 
This brewer meets 

      

 Standard 4 only when installed,        

operated and maintained in accordance with the enclosed        
instructions. 

AGENCY LISTING INFORMATION 

CAUTION:  

 

ELECTRICAL DAMAGE 

 

DO NOT plug in or energize this 
appliance until all 

Installation     

Instructions 

are read and followed.  

Damage to the Brewer will occur if 
these instructions are not followed. 

 

CAUTION:   

BURN HAZARD  

 

Exposed surfaces of the            
appliance, brew chamber and   
airpot may be HOT to the touch, 
and can cause serious burns. 

E9253

STD 4

E9253

Summary of Contents for Horizon 0420

























Reviews: