7
HDE-8C-QAM
Instruction Manual
Description:
Front panel connectors and indicators:
-20dB QAM RF TEST:
“F” connector for RF testing @ 20db below the main QAM RF output.
ASI OUT:
The “ASI OUT” BNC connector delivers any one (1) of the four (4) QAM output and is typically used as input to an
external modulator.
INPUT STATUS LEDs:
LEDs indicate the status of audio and video of each of the eight (8) inputs plus the spare input as follows:
Audio LED
Green = Audio input is detected and has no errors
Red = Audio input with error
Off = Audio input not detected
Video LED
Green = Video input is detected and has no errors
Red = Video input with error
Off = Video input not detected
Audio and Video LED’s in Spare Mode
When the Spare Mode is enabled, both audio and video LEDs on the spare input (#9) and its user assigned
replacement input will blink green. The LED indicators will return to their previous states when the mode is
disabled.
Audio and Video LED’s in EAS Mode
When EAS is activated, the Audio LEDs will change one at a time to red starting from Input # 1 and moving right
towards Input #8. The sequence continues on the Video LED row, again starting at input #1 and moving right.
After all LEDs are have turned red they all simultaneously switch back to green and the cycle begins again,
continuing until EAS has been deactivated.
IP RESET:
When pushed and held for about 10 seconds, the power LED will blink once to confirm reset operation. The
encoder defaults to the original IP address, Usernames, and Passwords as shipped from the Factory (shown below).
IP address = 172.16.70.1
Username = Admin (case-sensitive)
Password = pass (case-sensitive)
POwER:
LED is Green = AC power is detected.
LED is off = indicates (i) AC power is not connected, or (ii) AC power is connected but the power supply is defective.
The unit must be sent to blonder Tongue for repair for condition (ii).
3
5
4
1
2
1
2
3
4
5
7
HDE-8C-QAM
Instruction Manual
Description:
Front panel connectors and indicators:
-20dB QAM RF TEST:
“F” connector for RF testing @ 20db below the main QAM RF output.
ASI OUT:
The “ASI OUT” BNC connector delivers any one (1) of the four (4) QAM output and is typically used as input to an
external modulator.
INPUT STATUS LEDs:
LEDs indicate the status of audio and video of each of the eight (8) inputs plus the spare input as follows:
Audio LED
Green = Audio input is detected and has no errors
Red = Audio input with error
Off = Audio input not detected
Video LED
Green = Video input is detected and has no errors
Red = Video input with error
Off = Video input not detected
Audio and Video LED’s in Spare Mode
When the Spare Mode is enabled, both audio and video LEDs on the spare input (#9) and its user assigned
replacement input will blink green. The LED indicators will return to their previous states when the mode is
disabled.
Audio and Video LED’s in EAS Mode
When EAS is activated, the Audio LEDs will change one at a time to red starting from Input # 1 and moving right
towards Input #8. The sequence continues on the Video LED row, again starting at input #1 and moving right.
After all LEDs are have turned red they all simultaneously switch back to green and the cycle begins again,
continuing until EAS has been deactivated.
IP RESET:
When pushed and held for about 10 seconds, the power LED will blink once to confirm reset operation. The
encoder defaults to the original IP address, Usernames, and Passwords as shipped from the Factory (shown below).
IP address = 172.16.70.1
Username = Admin (case-sensitive)
Password = pass (case-sensitive)
POwER:
LED is Green = AC power is detected.
LED is off = indicates (i) AC power is not connected, or (ii) AC power is connected but the power supply is defective.
The unit must be sent to blonder Tongue for repair for condition (ii).
3
5
4
1
2
1
2
3
4
5
1
6
-20dB QAM RF TEST:
“F” connector for RF testing @ 20dB below the main QAM RF output.
ASI OUT:
The “ASI OUT” BNC connector delivers any one (1) of the four (4) QAM output and is typically used as input to an
external modulator.
INPUT STATUS LEDs:
LEDs indicate the status of audio and video of each of the eight (8) inputs plus the spare input as follows:
Audio LED
Green = Audio input is detected and has no errors
Red = Audio input with error
Off = Audio input not detected
Video LED
Green = Video input is detected and has no errors
Red = Video input with error
Off = Video input not detected
Audio and Video LED’s in Spare Mode
When the Spare Mode is enabled, both audio and video LEDs on the spare input and its user assigned replacement input
will blink green. THe LED indicators will return to their previous states when the mode is disabled.
Audio and Video LED’s in EAS Mode
When EAS is activated, the Audio LEDs will change on at a time to red starting from Input # 1 and moving right toward
Input #8. The sequence continues on the Video LED row, again starting at input #1 and moving right. After all LEDs
have turned red they all simultaneously switch back to green and the cycle begins again, continuing until EAS has been
deactivated.
IP RESET:
When pushed and held for about 10 seconds, the power LED will blink once to confirm reset operation. The encoder
defaults to the original address, Usernames, and Passwords as shipped from the Factory (shown below).
IP address = 172.16.70.1
Username = Admin (case-sensitive)
Password = pass (case-sensitive)
POWER:
LED is Green = AC power is detected.
LED is off = indicates (i) AC power is not connected, or (ii) AC power is connected but the power supply is defective.
The unit must be sent to Blonder Tongue for repair for condition (ii).
DATA OUT 1 GIGE:
RJ45 connector for GigE (1000Base-T Ethernet) interface for SPTS or MPTS output streams.
Only static IP address can be assigned to this interface. The factory default value is 192.168.252.1.
2
3
4
5
6
