Blonder tongue FRRA-S4A-860-43P Instruction Manual Download Page 3

3

FRRA Series  

Instruction Manual

Optical Receiver

Bandwidth:  47 to 860 MHz
Bandpass Flatness:  2.0 dB P/V
Operating Wavelength:  1310/1550 nm
Optical Input Range:  -6.0 to +3.0 dBm
Output Impedance:  75 ohm
CNR -1 dBm Input, 40 Ch. Load:  57 dB
CNR -1 dBm Input, 79 Ch.+ Data:  55 dB
CNR -1 dBm Input, 110 Ch. Load:  54 dB
Input Connector:   FRRA-S4A-xx:  FC/APC 

FRRA-S4S-xx:  SC/APC

Distribution Amplifier

Impedance - All Ports:  75 ohm
Return Loss Output:  16 dB
RF Gain:  43 dB
Test Port:  -20, ±2 dB
Gain Control Range:  10 dB 

Slope Control Range:  8 dB
Operating Temperature:  -20 to +45˚C
Power Supply Requirements 117 VAC, 60 Hz:  28 W
Size (W x H x L):  19 x 1.75 x 6.25 in., 48.26 x 4.45 x 15.88 cm
Weight:  5.75 lbs., 2.61 kg
Number Of Hybrids:  2
Hybrid Technology:  Power Doubling

Varying Specifications

   
Channel Loading:  

110

Flatness: 

± 0.5

Output Level (Low/High) 

34/42

Composite Triple Beat (CTB)

(a,b,c)

-60

Composite Second Order (CSO)

(a,b,c)

:  -58

Hum Modulation: 

-70

The FRRA is a fiber optic receiver integrated with the Blonder Tongue RMDA rack mount distribution amplifier.   

The FRRA may be used as a launch amplifier in a coaxial distribution network after networking with fiber. The fiber 

receiver provides a robust system for transferring 110 channels (depending on model) VSB/AM modulated signals 

over a single mode fiber. The FRRA operates with the FIBT Series of transmitters as well as with the transmitters of 

many other leading manufacturers. The FRRA-S4A-860-43-PA can transfer 79 channels of VSB/AM signals, plus 57 

digital QAM channels in the upper frequency range.

Description

Specifications-LINK(d) @ 25°C, Single-mode Fiber (Typical)

NOTES:
(a)  At specified channel loading at rated output capability
(b)  Distortion levels improve as output level is reduced
(c)   Distortion specifications at 8 dB sloped output
(d)  Assumes FIBT transmitter link and -1 dBm optical input

48

50

52

54

56

58

60

62

64

-10

-8

-6

-4

-2

0

+2

+4

Optical Input Level

CNR

110 Ch.

79 Ch. & data

40 Ch.

24 Ch.

10 Ch.

5 Ch.

CNR

Summary of Contents for FRRA-S4A-860-43P









Reviews: