manualshive.com logo in svg

Blodgett CONVEYOR OVEN MT1820E, Installation Operating & Maintenance Manual

Share
Download
Blodgett CONVEYOR OVEN MT1820E Installation Operating & Maintenance Manual Download Page 20

Maintenance

16

Troubleshooting Guide

POSSIBLE CAUSE(S)

SUGGESTED REMEDY

SYMPTOM: Blower motor(s) not running

S

Power switch turned OFF

S

No power to oven

S

Bad capacitor

S

Motor(s) burned out

S

Turn to ON position

S

Replace main fuses or reset breakers

S

Replace capacitor

S

*

SYMPTOM: Oven will not heat (heat on light will not come on).

S

Temperature controller not properly installed

S

Internal problem with main temperature controller

S

Loose probe connections at main temperature

controller

S

Short in probe

S

Reinstall

S

*

S

*

S

*

SYMPTOM: Elements will not heat.

S

Power switch turned OFF

S

Main temperature controller not set above

ambient temperature

S

Defective main temperature controller

S

Defective heating relay

S

Turn to ON position

S

Set to desired temperature

S

*

S

*

*Denotes remedy is a difficult operation and should be performed by qualified personnel only. It is recommended, however, that

All repairs and/or adjustments be done by your local Blodgett service agency and not by the owner/operator. Blodgett cannot as-

sume responsibility for damage as a result of servicing done by unqualified personnel.

WARNING!!
Always disconnect the power supply before cleaning or servicing the oven.

Summary of Contents for CONVEYOR OVEN MT1820E























Reviews:

No comments

Brands by name

Popular brands

Load more brands