background image

BLODGETT

www.blodgett.com

44 Lakeside Avenue, Burlington, VT 05401 • Toll Free: (800) 331-5842 • Phone: (802) 860-3700 • Fax: (802) 864-0183

CB24G-K

SHORT FORM SPECIFICATIONS

Provide Blodgett model CB24G-6K (6 pan) one 6 gallon direct steam kettle or model CB24G-10K (6 pan) one 10 gallon direct steam kettle on a 140,000 BTU gas boiler base base.
The kettles shall have a double wall interior to form a steam jacket around the lower 2/3 of the kettle. The bottom of the kettle shall be of hemispherical design for superior heat circula-
tion. Steam control valve mounted in leg. The tubular stainless steel mounting legs shall have the steam supply and condensate return pipes completely concealed within the leg meme-
bers. The sealed stainless steel tilt mechanism bearings shall permit the kettle to tilt forward 90° for complete emptying. A removeable operating handle with heat proof knob shall be
mounted on the left or right. Unit shall have a single support leg with nylon insert. Construction shall be all welded satin finish 304 stainless steel with a 316 stainless steel liner.
The boiler shall be suitable for operation at any pressure from 5-11 PSI (34-76 kPa) and operate on 115 VAC. Boiler shall be mounted in cabinet base. Polished stainless steel cabinet
base shall be of modular design to match other Blodgett steam equipment. Unit shall have 6” (152mm) stainless steel legs and adjustable bullet feet, reinforced stainless steel counter top
and hinged doors with magnetic latches. All piping shall be confined within the cabinet. Unit shall be automatically filled with water and brought to pressure when power switch is turned
on. Cold water condenser shall automatically condense exhausted steam in water before releasing it to drain. Boiler controls shall include automatic water level, pressure gauge, water
gauge glass, pressure control with pressure safety control, safety relief valve, cathodic protector and CSD-1 secondary low water cut off.
Unit shall have a hot and cold water faucet with control valves, 5" (152 mm) deep sink with drain and  two splash guards.
Kettles and boiler shall be ASME code stamped and National Board registered. Provide options and accessories as indicated.

Printed in U.S.A.

NOTE:

FOR COMMERCIAL USE ONLY

NOTE:

The company reserves the right to make substitutions of components without prior notice.

NOTE: SPLASH GUARD NOT SHOWN ON FRONT VIEW

DIMENSIONS ARE IN INCHES [MM]

REAR FLANGED

FOOT DETAIL

7/16" [11mm] HOLES

ON 2.5 [63] B.C.

2 EQUALLY SPACED

Ø

B

S

18

[457]

75

[191]

6.5

[165]

C

2.75

[70]

0.25

[6]

D

26

[660]

C

6 [152]

75 [191]

24” CABINET, 200,000 BTU

D

C

S

36” CABINET

24” CABINET

S

K

G

F

D

H

E

J

L

33

[838]

M

24 [610]

36 [914]

A

B

C

D

E

F

G

H

J

K

L

M

MODEL

CB24G-6K

CB24G-10K

12 (305)
16 (406)

14.5 (368)

15 (381)

56.75 (1441)
55.75 (1416)

3 (76)

2.5 (64)

5.75 (146) 4.75 (121)

3.5 (89) 11 (279)

8 (203)

12 (305)

9 (229)

6 (152)

APPROVAL/STAMP

P/N S00104 Rev A (7/07)

WATER SUPPLY:

Water quality is a major factor affecting the performance of your steamer. If you are
unsure of water quality, consult a local water treatment specialist and have the water
analyzed. Your water supply must be within these general guidelines:

Total dissolved solids: Less than 60 PPM

Total alkalinity: Less than 20 PPM

Silica:

Less than 13 PPM

Chlorine:

Less than 1.5 PPM

pH Factor:

7.0 - 8.5

Water which fails to meet these standards should be treated by installation of a water
conditioner. Failure or malfunction of this steamer due to poor water quality is not cov-
ered under warranty.

WATER & DRAIN CONNECTIONS:

Drain

2” (51mm) IPS piped to open floor drain. No solid connection.
24” length before open air opening (no bends or elbows)

Cold Water

3/8” (10mm) tubing at 25-50 PSI (170-345 kPa)

Steam Take Off 3/4” IPS optional to operate adjacent equipment

GAS SUPPLY:

3/4" IPS supply line required

Minimum Inlet Pressure:

Natural

7.0" W.C. static to unit

Propane

11.0" W.C. static to unit

POWER SUPPLY:

Unless otherwise specified, field wire electrical con-
nection to be 120VAC, single phase, 60 Hz with
grounding wire.

PRODUCT CLEARANCE

Right and Left side

3” (76mm)

Rear

6” (152mm)

SHIPPING INFORMATION:

Approx. Weight:

CB24G-6K

450 lbs. (204 kg)

CB24G-10K

470 lbs. (213 kg)

Reviews: