background image

 

 

Features 

 

 

Operating frequency 8.0 kHz Induction Balance 

 

Adjustable operating frequency (+/-60Hz) 

 

Operating mode: motion 

 

Audio discrimination 

 

Able to handle the harshest terrain and operate where other VLF 
machines have difficulty 

 

Standard 28cm (11") DD search coil 

 

Optional 38cm (15") DD search coil 

 

Optional 18cm (7") DD search coil (2013) 

 

Built-in LiPo battery 11.1V, 2200mAh – lasts 30 hours on one charge 

 

Automatic LiPo battery charger 

 

Manual and Automatic ground balance modes 

 

Coarse and Fine settings in manual ground balance mode 

 

Extremely fast processing allows good targets to be heard next to iron 

 

Adjustable sounds (frequency / tone) of target response 

 

Adjustable Silencer to reduce or eliminate “chatter” 

 

Adjustable audio Threshold and Volume control 

 

Discriminator switch with three independent modes of discrimination 

 

Adjustable Discrimination Level for detection/rejection of iron, tin-foil 
and low-grade non-ferrous metals (usually ground pollutants) 

 

Adjustable Depth of Discrimination 

 

LED low battery indicator 

 

6.35mm (1/4") Stereo headphones outlet 

 

Single charge operating time: up to 30 working hours 

 

Consumption: min: 35mA, max: 100mA 

 

Detachable and adjustable shaft construction made from aluminum 
and carbon fibre 

 

Robust and comfortable handle and armrest 

 

Light Electronic block with a robust control box made from ABS & 
aluminum 

 

Electronic block (control box) located under the armrest 

 

Electronics fully shielded against electromagnetic interference 

 

Cable for the search coil is double shielded against electromagnetic 
interference  

 

Gold-plated pins for the coil connector 

 

Gold-plated pins for the battery charger connector 

 

Total weight in ready to use condition: just under 4 lbs. 

 

RoHS compliant 

 

Developed and manufactured in Bulgaria 

 

3 year worldwide transferable warranty 

 

 

Summary of Contents for LTC64X v3














Reviews: