Blink Marine PKP2500SI Instructions Manual Download

Page: 8 / 38

www.blinkmarine.com

PKP2500SI_CANopenUM_REV1.0

8/38

12.

Set LED ON message

The keypad must be activated, see NMT Start CANopen Node message.

•

PKP 2500SI

Identifier

200h + current CAN ID

Default 215h

Byte 0

R8 R7 R6 R5

–

R4 R3 R2 R1

Red LED

Byte 1

0 0 0 0

–

0 0 R10 R9

Byte 2

G8 G7 G6 G5

–

G4 G3 G2 G1

Green LED

Byte 3

0 0 0 0

–

0 0 G10 G9

Byte 4

B8 B7 B6 B5

–

B4 B3 B2 B1

Blue LED

Byte 5

0 0 0 0

–

0 0 B10 B9

Byte 6,7

00h

Not used

Examples:

Direction

Identifier

Format

Message

LED

To Keypad

215

Std

00 00 00 00 00 00 00 00

Turn OFF all the LED

To Keypad

215

Std

01 00 00 00 00 00 00 00

Only red LED #1 ON

To Keypad

215

Std

00 03 00 00 00 00 00 00

Red LED #9 and #10 ON

To Keypad

215

Std

00 00 10 00 00 00 00 00

Only green LED #5 ON

To Keypad

215

Std

00 00 80 00 00 00 00 00

Only green LED #8 ON

To Keypad

215

Std

00 00 00 00 FF 03 00 00

All LED blue ON

To Keypad

215

Std

FF 03 FF 03 00 00 00 00

All LED amber ON

Summary of Contents for PKP2500SI







































Search results

Summary of Contents for PKP2500SI

Reviews:

Related manuals for PKP2500SI

Brands by name

Popular brands

Blink Marine PKP2500SI, Instructions Manual

Search results

Summary of Contents for PKP2500SI

Reviews:

Related manuals for PKP2500SI

Brands by name

Popular brands