Blink Marine PKP2500SI Instructions Manual Download

Page: 6 / 38

www.blinkmarine.com

PKP2500SI_CANopenUM_REV1.0

6/38

Stop CANopen node

Identifier

00h

Byte 0

XXh

02h: Stop CANopen node
00h: Stop CANopen node
(old PKP sw compatibility)

Byte 1

YYh

Keypad CAN ID
00h: stop all the keypads

15h: stop the keypad with CAN ID = 15h.

Byte 2, 7

00h

Not used

Example:

Direction

Identifier

Format

Message

To Keypad

Std

02 15

Boot-up service

This service is used to signal that a NMT slave has entered the NMT state Pre-operational.

Identifier

700h + current CAN ID

Default 715h

Byte 0

00h

One data byte is transmitted with value 0.

Example:

Direction

Identifier

Format

Message

From Keypad

715h

Std

00h

The keypad with CAN ID 15h has entered the NMT state Pre-operational.

Heartbeat message

The heartbeat mechanism for a CANopen device is established by cyclically transmitting the
heartbeat message by the heartbeat producer.

Refer to

Object 1017h

for more details.

10.

Sync message

This mechanism modifies the PDO operation in the following way: both the RPDOs and TPDOs are
stored at the receiving of the 1

SYNC message but, while the RPDOs are always processed with

the arrival of next one, the TPDOs are transmitted each n-th time the SYNC message is received
depending on the value chosen for transmission type. The structure of the SYNC message is:

Refer to Objects

1400

1401

1800h

for more details.

Identifier

80h

No data byte is transmitted

Summary of Contents for PKP2500SI







































Search results

Summary of Contents for PKP2500SI

Reviews:

Related manuals for PKP2500SI

Brands by name

Popular brands

Blink Marine PKP2500SI, Instructions Manual

Search results

Summary of Contents for PKP2500SI

Reviews:

Related manuals for PKP2500SI

Brands by name

Popular brands