background image

BrewEasy™ Compact Tri-Clamp V1 

© Blichmann Engineering, LLC 2021 

For replacement parts, visit: blichmannengineering.com/genuine-replacement-parts

1

BrewEasy

 Compact TC

Assembly, Operation, & Maintenance

Congratulations on your purchase and thank you for selecting the BrewEasy™ Compact 

from Blichmann Engineering™. We are confident that it will provide you years of service 

and many gallons of outstanding beer. This manual will familiarize you with the use, 
assembly, and sanitation procedures for the product.

Sections labeled “Warning” can lead to serious injury or death if not followed. Please thoroughly read these sections 

and understand them completely before use. If you do not understand them or have any questions, contact your  

retailer or Blichmann Engineering (www.BlichmannEngineering.com) before use.

 

Sections labeled “Caution” can lead to equipment damage or unsatisfactory performance of the equipment. Please 

read these sections thoroughly. If you have any questions, contact your retailer or Blichmann Engineering  

(www.BlichmannEngineering.com) before use.

 

Sections labeled “Important” should specifically be followed to ensure satisfactory results with the product. 

WARNING:

CAUTION:

 

IMPORTANT:

IMPORTANT INFORMATION

PLEASE READ AND THOROUGHLY UNDERSTAND THIS MANUAL PRIOR TO USE  

FOR IMPORTANT SAFETY INFORMATION!

Brewing has inherent hazards and requires care, focus, and a mindset of safety and precaution.  Hot liquids, steam, flame, 

electricity, heavy lifting, slippery surfaces, cuts, and harsh chemicals to name a few.  

•  Always thoroughly read and understand all product manuals before using the product.

•  Always keep children and pets safely away from the brewing area.

•  Always wear protective clothing, safety glasses/goggles, shoes, and burn/chemical resistant gloves.

•  Always use GFCI protected circuits for ALL electrical equipment.

• 

Always keep flame away from flammable surfaces.

•  Always brew on hard surfaces such as concrete.

•  Always disconnect electrical equipment from power and propane tanks after each use.

•  Never lift hot and/or heavy liquids.

•  Never use drugs or alcohol while brewing.

•  Never leave the brewing area unattended.

Summary of Contents for BrewEasy Compact TC









Reviews: