background image

5 BBL Insulated Hybrid Brewhouse V1 

© Blichmann Engineering, LLC 2018 

For replacement parts, visit: blichmannengineering.com/genuine-replacement-parts

1

5 BBL Insulated Hybrid Brewhouse

Assembly, Operation, & Maintenance

Congratulations on your purchase, and thank you for selecting the 5 BBL Hybrid 

Brewhouse from Blichmann Engineering™. We are confident that it will provide you 
years of service and many gallons of outstanding beer. This manual will familiarize 

you with the use, assembly, and the sanitation procedures for the product.

Sections labeled “Warning” can lead to serious injury or death if not followed. Please thoroughly read these sections 

and understand them completely before use. If you do not understand them or have any questions, contact your  

retailer or Blichmann Engineering (www.BlichmannEngineering.com) before use.

 

Sections labeled “Caution” can lead to equipment damage or unsatisfactory performance of the equipment. Please 

read these sections thoroughly. If you have any questions, contact your retailer or Blichmann Engineering  

(www.BlichmannEngineering.com) before use.

 

Sections labeled “Important” should specifically be followed to ensure satisfactory results with the product. 

WARNING:

CAUTION:

 

IMPORTANT:

IMPORTANT INFORMATION

PLEASE READ AND THOROUGHLY UNDERSTAND THIS MANUAL PRIOR TO USE 

 

FOR IMPORTANT SAFETY INFORMATION!

What’s In the Box?

Item Number

Description

Quantity

BEPS-BK-5BBL-SW

5 BBL Boil Kettle

1

BEPS-HLT-5BBL-SW

5 BBL Hot Liquor Tank

1

BEPS-MLT-5BBL-SW

5 BBL Mash Tun

1

Controller

1

Sanitary Heater Set of 3

2

BEPS-PUMP-15HP

1/5hp Brewery Pump

1

BEPS-Pump-1HP

1HP Brewery Pump

1

BEPS-CHILLER-2.0SQM

Chiller 3.5 BBL

1

BEPS-HoseKit-5

5 Hose Assembly Kit

1

BE-000957-00

CIP Spear 1.5” Tri Clamp

1

BE-000859-00

Cap 2.5” Sanitary

3

BE-000861-00

2.5” Tri Clamp

3

Item Number

Description

Quantity

BE-000868-00

Clamp Gasket 1.5”

17

BE-000633-00

1.5” Tri Clamp

17

BE-000863-00

Tri Clamp Elbow 1.5”

6

BE-001356-00

1.5” Multi Position Valve Tri Clamp

5

BE-001084-00

CIP Spray Ball

1

BE-001186-00

1.5” Sanitary Pipe 6”

1

BE-000630-00

Cap 1” & 1.5” Sanitary

2

BE-001132-01

3.5 BBL Stand Pipe

2

BE-000866-00

Clamp Gasket 2.5”

3

BE-001482-00

6” Tri Clamp Cap

1

BE-001478-00

6” Tri Clamp

1

BE-001479-00

6” Gasket

1

Summary of Contents for 5 BBL Insulated Hybrid Brewhouse









Reviews: