BLH NOBEL G5 Manual Download Page 11 | Manualshive

Page: 11 / 32

BLH NOBEL G5 Manual Download Page 11

G5 Weighing Instrument

2-5

ControlNet Module

ControlNet module front view

(1) Network Status LED A.

(2) Module Status LED.

(3) Network Status LED B.

(4) ControlNet connector A.

(5) ControlNet connector B.

Network Status LED A/B

LED

State

Indication

LED A and B Off

Not online / No power

Flashing Red (1 Hz)

Incorrect node configuration, duplicate MAC ID
etc.

Alternating Red/Green Self-test of bus controller

Red

Fatal event or faulty unit

LED A or B

Off

Channel is disabled

Alternating Red/Green Invalid link configuration

Flashing Green (1 Hz) Temporary errors (node will self-correct) or

node is not configured to go online

Green

Normal operation

Flashing Red (1 Hz)

Media fault or no other nodes on the network

Status LED

State

Indication

Off

No power

Green

Operating in normal condition, controlled by a Scanner in
run state

Flashing Green (1 Hz)

The module has not been configuration or Scanner in idle
state

Red

Unrecoverable fault(s), EXCEPTION, fatal event

Flashing Red (1 Hz)

Recoverable fault(s), MAC ID has been changed after
initialization etc.

ControlNet connectors

These connectors provide ControlNet connectivity. If redundancy is wanted both
connectors should be used. Otherwise either connector can be used.

A

B

ControlNet

B

(1)

(2)

(3)

(4)

(5)

«
...
9
10
11
12
13
...
»

Summary of Contents for G5

































Reviews:

No comments