background image

 16

SECTION 6: WARRANTY AND SERVICE

6.1 WARRANTY DESCRIPTION

MOTOR:

Standard Blendtec United States (US) warranties are as follows:
Chef Blender

2 years or 15,000 cycles

Standard Blendtec International (outside US) warranties are as follows:
Chef Blender 

2 years parts, 1 year labor

JAR:

The jar and internal bearing assembly are warrantied against failure as follows:

Jar Model 

Warranty

40-501, 40-502, 40-503 

180 days from purchase date

40-505, 40-508 

1 year from purchase date

The jar model number can be found under the NSF logo on the jar.

BLADES:

The stainless steel blade is warrantied against breakage for the life of

the jar. Please note that dulling of the blade may occur as a result of

usage and does not affect blending effectiveness.

SOUND ENCLOSURE:

The sound enclosure is warrantied for 90 days against manufacturing

defects.

DRIVE SOCKET:

The drive socket (see Fig. 1.2) is warrantied for the life of the machine.

Warranties begin from date of shipment, or on date of purchase where

proof of purchase is provided. Cosmetic damage and abuse are not

included within this warranty.

6.2 SERVICE PROCEDURE

Should you experience any difficulty in using your Blendtec blender,

please do the following:

UNDER WARRANTY

Summary of Contents for Brawn and Brains CHEF

























Reviews: