ENGLISH |
Wireless Indoor Siren (SR-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Mounting Holes x 4
2. Tamper Switch
The tamper switch protects the cover from being opened.
3. Function Switch Block
Contains 7 DIP Switches to enable the learning mode and to set
the alarm period of siren.
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x Indoor Siren
4 x large wall plugs and screws
4 x 1.5V D alkaline batteries
D
D
i
i
p
p
S
S
w
w
i
i
t
t
c
c
h
h
1. Open the front cover
2. Open the battery compartment cover to insert batteries.
3. Locate the Function Switch Block. Use a sharp object to set
Dip SW3 & SW4 on the function switch block to your desired
alarm length.
4. Enter learning mode for your control panel.
5. Slide Dip SW1 to the ON position. SR-S1 will enter learning
mode. After 3 seconds, the Siren will send a learning code
and emit a beep to confirm.
6. If the Control Panel receives the learning signal, please refer
to the Control Panel manual to complete the learning process.
When learning is complete, the Control Panel will send signal
to the Siren to confirm. The Siren will sound a short beep
again to indicate learning is successful.
If the Control Panel fails to receive a learning code, slide Dip
SW1 back to OFF, and then ON position again to enter
learning mode again.
7. If the Siren does not respond, please remove the Siren from
the control panel and repeat steps 4-6 again.
8. Slide Dip SW1 to the OFF position to leave learning mode. If
you do not slide Dip SW1 back to OFF position, the Siren will
automatically leave the learning mode in one hour.
The Indoor Siren has 4 mounting holes on the back cover for wall
mounting.
Before Installation, refer to your Control Panel manual to
temporarily disable the Siren Tamper function to avoid
accidental alarm trigger.
1. Use the 4 mounting holes on the back to mark position on the
wall.
2. Drill holes into the wall using the mounting holes as template,
insert wall plugs if required,
3. Fix the base onto the wall with the screw and plugs provided.
4. Replace the front cover onto the base.
5. Enable the Siren Tamper function on you Control Panel.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
SW1
Siren Learning
OFF
Normal operation
ON
Learn-in mode
SW2
Reserved
SW3
SW4
Siren Duration
OFF
OFF
3 min.
ON
OFF
5 min.
OFF
ON
10 min.
ON
ON
1 second (test)
SW5
Reserved
SW6
Memory Reset
OFF
Normal
ON
Clear Memory
SW7
Supervision
OFF
Supervision function disable
ON
Supervision function enable
For further detail please see
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
a
a
n
n
d
d
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
.
.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Mounting Holes
x 4