“
＊
” + “6”
Change Keypad PIN Code:
1. Enter old code + “
” Key
2. Enter new 4-
digit code + “#” key
“
＊
” + “8”
Enable Arming without Use PIN code
function
“
＊
” + “9”
Enable Arm with User PIN code function
(
Default
)
“Disarm” twice
To leave Test Mode
A
A
r
r
m
m
/
/
H
H
o
o
m
m
e
e
/
/
D
D
i
i
s
s
a
a
r
r
m
m
If Remote Keypad is set to
“Arm with Use PIN code” (“
＊
” + “9”
under Test Mode)
Away Arm
Enter a Control Panel User PIN Code +
“Arm” Key
Home Arm
Enter a Control Panel User PIN Code +
“Home” Key
Disarm
Enter a Control Panel User PIN Code +
“Disarm” Key
If Remote Keypad is set to
“Arm without Use PIN code” (“
＊
” + “8”
under Test Mode)
Away Arm
Press
“Arm” Key
Home Arm
Press
“Home” Key
Disarm
Enter a Control Panel User PIN Code +
“Disarm” Key
D
D
u
u
a
a
l
l
K
K
e
e
y
y
A
A
l
l
a
a
r
r
m
m
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
Dual Key Alarm function will activate alarm when both keys are
pressed at the same time. To use the functions, please enable
them under Test Mode. (Default are disabled)
“1” + “3”
Panic Alarm
“4” + “6”
Fire Alarm
“7” + “9”
Emergency Alarm
L
L
E
E
D
D
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
s
s
A
A
c
c
t
t
i
i
v
v
e
e
L
L
E
E
D
D
The Active LED light up whenever any key is pressed.
Off
Keypad in Standby Mode
Green LED On
Keypad in Normal Operation
Green LED Flash
Keypad in Test Mode
T
T
r
r
a
a
n
n
s
s
m
m
i
i
s
s
s
s
i
i
o
o
n
n
L
L
E
E
D
D
The Transmission LED lights up whenever the Keypad transmits
a radio signal
F
F
a
a
u
u
l
l
t
t
L
L
E
E
D
D
The Fault LED light up when the Keypad is activated under fault
condition
Orange LED On
Keypad tamper switch is triggered
Orange LED Flash Keypad is under low battery
B
B
a
a
t
t
t
t
e
e
r
r
y
y
The Remote Keypad uses one 3V CR2450 lithium battery as its
power source. It also features low battery detection function to
notify the Control Panel when battery voltage is low.
When the Remote Keypad is on low battery, follow the procedure
below to change the battery.
1. Open the back cover.
2. Remove the old battery carefully with a minus screw driver by
inserting the screw into gap in battery compartment, the lift the
battery as picture below.
Do not remove the battery by hand to avoid risk of damaging
the battery compartment.
3. Press any key several times to fully discharge.
4. Insert the new battery observing correct polarity.
5. Replace the back cover.
F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you forget your Keypad PIN code, or the Remote Keypad has
any problem, you can reset the Remote Keypad to factory
default.
1. Open the back cover.
2. Open the back cover and remove the battery.
3. Press and hold
“3” key and insert battery.
4. The Remote Keypad will sound 3 short beeps.
5. Release
“3” key, the reset process is now complete
E
E
n
n
v
v
i
i
r
r
o
o
n
n
m
m
e
e
n
n
t
t
a
a
l
l
C
C
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
-10
°
C to 40
°
C, relative humidity 85% non-condensing.
R
R
a
a
d
d
i
i
o
o
868 MHz
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n