Blaupunkt HEILBRONN RCC 24 Operating Instructions Manual Download Page 6

17

Heilbronn RCC 24

DE

UT

S

C

H

EN

GLI

S

H

IT

A

L

IANO

POR

T

UG

UE

S

NE

DE

RL

AND

ESP

A

OL

SVEN

SK

A

F

RANÇAI

S

Important information

What you need to know!

Before starting to use your new car radio you
should carefully read through the information
on “Traffic safety” and “Anti-theft coding”.

Traffic safety

Traffic safety has always priority. Use your
car radio in such a manner that you are
always able to cope with and react to the
prevailing traffic situation at any given time.
Remember, even at 50 km/h you are still
moving at a speed of 14 m per seconds.
It is also very important that you are able to
hear, and react to, acoustic warning signals
around you, for example from the police or
the firebrigade.
Therefore, adjust the volume reasonably.

Installation/connection

The code system can only be switched on
and off, if the radio is connected to perma-
nent power.
If you like to install your new car radio by
yourself or add other audio components to
the existing ones, then please read carefully
the enclosed instructions on installation and
connection.
Do not connect the loudspeaker outputs to
ground!
Only use the accessory and replacement
parts approved by Blaupunkt.

Anti-theft coding

The car radio comes standard with the code
system deactivated.
If the anti-theft coding system is on while the
power supply to the unit is interrupted (e.g.
theft, disconnecting the car battery), the set is
electronically blocked. Then it may only be
used again after the appropriate code num-
ber has been entered (see car radio pass-
port).

Wrong code number entered

It should not be possible for thieves to ascer-
tain the code number by trial-and-error. This
is why the set will be blocked for a certain
period of time, if an incorrect code number is
entered. In this case, “- - - -” will appear in the
display.
This waiting time is 10 seconds after the first
three attempts, and 1 hour following subse-
quent attempts.
After 19 unsuccessful attempts, “OFF” will
appear in the display and the set can no
longer be restarted.

Note:
Keep you car radio passport with the code
number in a safe place in order to avoid
“unauthorized access” to your car radio.
If the power supply to the radio is interrupted
while the code system is switched on, you
need to know the right code number.

Summary of Contents for HEILBRONN RCC 24















Reviews: