background image

Remote Control

Disclaimer

• 

Recycling and Disposal

 

Do not dispose of your old unit in the

 

household trash!

 

Use the return and collection systems

 

available to dispose of the old device.

This manual may be updated from time to time 
without any notice.

A control solely via the right or left channel is 
also possible since the low-frequency portion 
of the music is generally identical on both 
channels.

In no event shall Blaupunkt be liable for any 
direct, indirect, punitive, incidental, special 
consequential damages, to property or life, 
improper storage, whatsoever arising out of 
or connected with the use or misuse of our 
products.

USA & CANADA : Product not intended for sale 
in the United States and Canada. If purchased 
in the U.S. or Canada, this product is pur-
chased as-is. No warranty, express or implied is 
provided in the U.S. and Canada.

                  

Proper system planning is vital in order to max-
imize the device’s performance and road safety. 
Plan your installation carefully to avoid compro-
mising performance reliability of the system. 
Consult an authorized Blaupunkt dealer for instal-
lation or reparation. Read the manual carefully 
before operating the device for the first time.

Safety Notes

Ensure to follow below safety notes during instal-
lation and wiring connection : -

Installation and Connection Instructions

Intergrated Fuse

Switching On/Off

Voltage Supply

1

INTRODUCTION

Disconnect the negative terminal of the 
battery. Refer to the safety notes of vehicle 
manufacturer.
Ensure positions of the holes are nowhere 
near the vehicle component to avoid any 
damage during drilling.
Ensure cross section of the cable is no less 
than 2.5mm2 if the positive and negative 
cables are too long.
Incorrect installation may result in malfunc-
tion of the device or the car sound system.

Select a dry and well-ventilated location to 
install the device.
The device must not be installed on the rear 
shelf, rear seats or exposed locations.
The installation location must be suitable for
screw holes and have stable ground support.

The integrated fuse in the device protects 
the output voltage and the entire electrical 
system in case of malfunction. Do not replace 
damaged fuse with higher current.

This device will automatically turn on if audio 
signal is detected. The device will also auto-
matically turn off if audio signal is received.

Use the supplied power extension cable to 
connect to the positive battery terminal.
Firmly and carefully connect the ground lead 
to a bare metal point on the vehicle chassis.
The control of the device should be a 
two-channel control, either via the preampli-
fier output of the car sound system.

Turn the sub level knob to adjust the volume 
to the desired level.

Summary of Contents for GTr 10150 A









Reviews: