Blaupunkt FIENE 500, User Manual, Page: 37 / 40

37
EN
1.Loosen the seat post clamp , keep the
bike steady , insert the seat post in the
frame.
1.When you need to adjust the height of
the saddle , first loosen the seat post clamp ,
then move the seat post to the preferred
height , tighten the seat post clamp
2.Adjust the screw ,tighten the clamp, then
press the saddle at full tilt to ensure the
seat post locked tight enough and doesn’t
rotate or move up and down .
1.Environmental temperature for charging is 0
℃
-45
℃
, for
discharging is -20
℃
-60
℃
, please keep the battery in dry condition
2.Do not put the battery in acidic or alkaline liquid , keep it away from
rain , fire , heat and high temperature environment .
3.Do not mis-connect the negative and positive electrodes of the
battery ; breaking , disassembling and short circuiting the battery are
prohibited .
4.Only charge the battery with the original charger of the bike , other
charger may cause battery leaking , heating , smoking and in serious
situation cause fire and explosion .
5.If the battery is not to be used in a long time , keep the battery in a
dry and cool environment , and charge it for 2 hours every two months
6.Charging according to the manual requirements , or else we won’t
take any responsibilities for the damages occurred
7.Charging in a dry and cool environment , do not charge in closed or
high temperature areas
8.Unplug the charger in time when the charging is done , do not plug
the charger to power source while not charging
9.When charging , plug the battery first , then connect the power source ;
When charging finished , disconnect the power source first , then unplug
the charger
10.If the charger indicator stops working or the charger over
heats and causes funny smell , unplug the charger
immediately and repair or replace the charger
11.Keep the charger away from fluids while using and storage ,
in case of short circuit , avoid any penetrations to the charger
12.Try not to carry the charger around with your bike , if you
must , make sure it’s well protected and store it in your tool box
13.Try to avoid the battery being fully discharged when using ,
to keep the battery in good condition and for a longer lifespan ,
try to only use the bike between battery level 20% to 100%
14.Do not disassemble or replace any parts of the charger by
yourself
15.Due to the capacity fade mechanisms of Lithium-Ion battery ,
the battery capacity will fade at
different temperatures , at -10
℃
the capacity will be 70% ,
at 0
℃
the capacity will be 80% , at 20
℃
the capacity will be 1
00%
16.Do not put the battery in places that may fall to the ground ,
in case it may cause battery
leakage , over heating that could lead to fire or explosion
2.The saddle height mustn’t exceed the
height limit screw or safety height limit line
Height limit screw
Safety height
limit line
4.Seat post assembling
Battery and charging
5.Adjustment of saddle height
1.Hold the bike body and turn the stem
upright to ensure that the stem is seamlessly
connected to the underside 2.Fasten the folding wrench directly in
the direction of the stem
Security button
3.Slightly shake the stem and check if the
security buckle is fully buckled..
4.When folding the stem, you need to
press the security buckle and then
open the folding wrench to it
1. Keep the e bike in a place where there is no direct sunlight or no rain after riding.
2. Regularly check each screw of the e bike and to be tightened, and tighten it regularly;
(Screw torque of each main position: the head tube screw: 180-220kgf.cm;
Saddle screw: 180-220kgf.cm; front wheel nut: 250-300kgf.cm; rear wheel nut: 300-350kgf.cm)
3.If there is stain on the surface of the e bike body, use a soft cloth to wipe by a small amount of water; do not use alcohol,
gasoline or other chemical solvents with corrosive and volatile, otherwise it will seriously damage the appearance or internal
structure of the e bike body.
4.Chain elastic standard: chain up and down ≤ 10mm; if the chain is loose, the rear wheel nut can be loosened, the chain
tensioner can be adjusted to the chain fastening state, and the rear wheel nut can be tightened.
5.If the disc brakes and the disc plate friction, adjusting the position to make them no interference friction.
If the disc plate skew heavy or the disc brake is disabled, then the disc or disc brake needs to be replaced.
6.Every 3 months, apply grease to the frame folding wrench screws and maintain the chain smear chain anti-rust oil.
7. If the shock absorber fails or is damaged, it is necessary to disassemble the original shock absorber and
replace a new shock absorber to achieve the best shock absorption effect.
Do not flush the e bike with water to avoid accidents caused by internal electronic components and wiring.
Storage and Maintenance 2.Unfold the stem
Regular maintenance & check
Tip: Please maintain and check the e bike regularly, to keep it in a best riding condition.
Maintenance part Maintenance purpose
Brake Check the brake function,prevent accidents caused by brake dysfunction
Tire Check the tires condition and pressure, in case tires bursting or over power consumption during riding
Tire Rim Check the rim conditions, clean dirt, in case rim breaks or get stuck
Shock absorber Check the shock absorber condition, clean and lubricant, keep it in a good working condition
Throttle Check throttle condition, in case dysfunction or malfunction
Wires Check if the wires ports are loose or broken in case of wiring faulty
Screws Check the screws in the main parts, in case they get loose or fall off
Battery
Check the appearance and the battery performance,
in case of wiring faulty, extend the lifespan of the battery
Charger Check if the charger cable are impact, input and output plug are reliable
Lubrication Check if the axles and brake lights need lubrication or not
Cleaning Keep the bike surface in a clean condition