background image

Where  a  flexible  hose  assembly  is  used,  ensure  it  is 
approved to AS/NZS 1869, Class B. Any hose assembly 
used  must  be  restrained  from  accidental  contact  with 
the flue outlet of an under bench oven. 
This hose assembly shall be suitable for connection to a 
fixed consumer piping outlet located as follows:
Hotplates at a point 800 mm to 850 mm above the floor 
and in the region outside the width of the appliance to a 
distance of 250 mm. 

After connecting to gas, check for leaks using soapy 
solution, never a naked flame.  

Inlet connection region for flexible hose

Gas Connection 

Install in accordance with relevant gas standards and/or codes of 
practice applicable.  
Connect the elbow fitting to the appliance gas manifold 
connection, and check that seals between the elbow and 
manifold connection are in place and in good condition.  

For Natural gas: connect the natural gas appliance
regulator (pictured

 

opposite) with integral test point using

approved gas thread tape or

 

compound to the elbow

fitting.

For Universal LPG: connect the brass test point adaptor
(pictured opposite)

 

using approved gas thread tape or

compound to the elbow fitting.

Ensure the supply connection point, test point and natural gas 
regulator  adjustment  screw  (for  Natural  gas  installation)  are 
accessible  for  testing  and/or  adjustment  with  the  hotplate  in 
the installed position.  

20

Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS

1869,10mmID,class B or D,no more than 

 m long and installed in 

accordance with AS/NZS 5601.1.

Ensure that the hose does not contact the hot surfaces of the 

hotplate,oven,dishwasher or any other appliance that may be installed 

underneath or next to the hotplate.The hose should not be subjected to abrasion, 

kinking or permanent deformation and should be able to be inspected along its 

entire length with the cooktop in the installed position. Unions compatible with 

the hose fittings must be used and all connections tested for gas leaks.The 

supply connection point shall be accessible with the appliance installed.

WARNING: Ensure that the hose assembly is restrained from accidental contact 

with the flue outlet of an underbench oven.

G

as 

C

onnection

1.2

Summary of Contents for 5GB61150AU





























Reviews: