BLAUBERG KOMFORT Ultra L 250-E User Manual Download Page 9

Page: 9 / 18

www.blaubergventilatoren.de

KoMFort ultra S/l 250-H/e

260 mm

Unit wall mounting

Suspended mounting

260 mm

3. Install the unit on the mounting brackets. Tighten the triangular fixing screws on the mounting brackets.

SUSPENDED MOUNTING USING L-SHAPED BRACKETS (only for KOMFORT Ultra S/L 250-E models)

When using the L-shaped brackets, the unit can be mounted close to the ceiling or on the threaded rods.

Screw

Dowel

min 400 mm

Nut

Threaded rod

Washer

Vibration absorbing

rubber

Washer

Nut and lock nut

Vibration absorbing

rubber

UNIT FLOOR MOUNTING

Install the unit on the pre-mounted floor supports, minimum 150 mm height, to ensure sufficient access for the drain pipe connection
to the U-trap and for condensate drain system installation.

150 mm

Summary of Contents for KOMFORT Ultra L 250-E



















Search results

Summary of Contents for KOMFORT Ultra L 250-E

Reviews:

Related manuals for KOMFORT Ultra L 250-E

Brands by name

Popular brands

BLAUBERG KOMFORT Ultra L 250-E, User Manual

Search results

Summary of Contents for KOMFORT Ultra L 250-E

Reviews:

Related manuals for KOMFORT Ultra L 250-E

Brands by name

Popular brands