background image

5

TECHNICAL DATA

The unit is designed for indoor application with the ambient temperature ranging from +1 

o

C up to +40 

o

C and relative humidity up to 80 %.

The unit is rated as a Class I electrical appliance.

Hazardous parts access and water ingress protection rating:

 

IP 44 for the unit motors

 

IP 22 for the assembled unit connected to the air ducts

The unit design is constantly being improved, so some models can slightly differ from those ones described in this manual.

TECHNICAL DATA

Model

Komfort Ultra 

EC L(S) 350-H

Komfort Ultra 

EC L(S) 350-E

Komfort Ultra 

L(S) 250-H

Komfort Ultra 

L(S) 250-E

Unit voltage [V /50-60 Hz]

1~ 230

Maximum unit power [W]

156

148

Maximum unit current [A] 

1,17

0.78

Maximum air capacity [m

3

/h]

350

250

R.p.m.

3200

2700

Sound pressure level at 3 m distance [dB(A)]

28-47

28-47

Transported air temperature [

o

C]

from -25 to +60

from -25 to +40

Insulation

20 mm mineral wool

Extract filter

G4 

Intake filter

G4 (F8 PM2.5 92 %)*

Connected air duct diameter [mm]

Ø

125

Weight [kg]

26

25

26

25

Heat recovery efficiency, %

85

85

85

85

Humidity recovery efficiency, %

50

50

Heat exchanger type

Cross flow

Heat exchanger material

aluminium

polymerized cellulose

aluminium

polymerized cellulose

* - Option

Model

A

A1

B

B1

C

C1

Komfort Ultra EC L350-H(E) S2

-

87

-

110

-

43

Komfort Ultra EC S350-H(E) S2

87

-

110

-

43

-

Komfort Ultra EC L350-H(E) S14

-

198

-

255

-

63

Komfort Ultra EC S350-H(E) S14

172

-

295

-

63

-

Komfort Ultra L250-H(E) S12

-

129

-

157

-

43

Komfort Ultra S250-H(E) S12

157

-

129

-

43

-

OVERALL DIMENSIONS OF THE UNIT, MM

284

284

810
713

443

443

C1

490

B

A

ø125

ø125

B1

A1

713

C

Komfort Ultra (EC) S 350 (250) - H(E)

Komfort Ultra (EC) L 350 (250) - H(E)

Summary of Contents for Komfort Ultra EC L350-E S14























Reviews: