BLAUBERG CDT E1 Operation Manual Download Page 14

14

TRANSPORTATION AND STORAGE RULES 

Transportation is allowed by any transportation vehicle provided that the product is in the manufacturer's original 
package.  
Store the delivered product in the manufacturer's original packing box in a dry ventilated premise with the 
ambient temperature  
from  +5 °C up to + 40 °C and relative humidity less than 80 %.  
The storage environment must be free of dust, acid or alkali vapours to prevent corrosion.  
 

DISPOSAL

Do not dispose in domestic waste. The unit contains in part material that can be recycled and in part substances 
that should not end up as domestic waste. 
Dispose of the unit once it has reached the end of its working life according to the regulations valid where you are.

MANUFACTURER'S WARRANTY  

The fan complies with the requirements according to the EU norms and directives, to the relevant EU-Low 
Voltage Equipment Directives, EU-Directives on Electromagnetic Compatibility. 
We hereby declare that the following product complies with the essential protection requirements of 
Electromagnetic Council Directive 2004/108/EC, 89/336/EEC and Low Voltage Directive 2006/95/EC, 73/23/EEC 
and CE-marking Directive 93/68/EEC on the approximation of the laws of the Member States relating to 
electromagnetic compatibility. This certificate is issued following test carried out on samples of the product 
referred to above. Assessment of compliance of the product with the requirements relating to electromagnetic 
compatibility was based on the following standards. 
Protection degree index according to IP rating against access to hazardous parts and water ingress – IP55. 
The fan does not require grounding.  
The manufacturer hereby warrants normal operation of the fan over the period of five years from the retail sale 
date provided observance of the installation and operation regulations. 
In case of failure due to faulty equipment during the warranty period the consumer has the right to exchange it. 
If case of no confirmation of the sale date, the warranty term shall be calculated from the manufacturing date.  
The replacement is offered by the Seller. 
 

Warning! 

The MANUFACTURER shall not be liable for any damage resulting from any misuse 
of or gross mechanic interference with the fan.

 

CDT(E) E

Summary of Contents for CDT E1





















Reviews: