BLAUBERG Ventilatoren KOMFORT EC S200 User Manual Download Page 10 | Manualshive

Page: 10 / 24

background image

www.blaubergventilatoren.de

KOMFOrt EC S(B)200/250(-E)

10

HUMIDITY SENSOR MOUNTING IN THE EXTRACT AIR DUCT

CAUTION!

The humidity sensor must be installed in the air duct prior to the unit mounting.

FS1 humidity sensor mounting sequence:

•  Remove the screws that retain the panel on side of the extract spigot and remove it.
•  Place the humidity sensor in the mount.
•  Connect the humidity sensor connector to the connector with a cable from the control unit. The connector is mounted by the

manufacturer.

FS2 humidity sensor mounting sequence:

•  Remove the screws that retain the panel on side of the extract spigot and remove it.
•  Place the humidity sensor in the mount.
•  Connect the humidity sensor connector to the connector with a cable from the control unit. The connector is mounted by the

manufacturer.

Extract
air duct

MOUNTING AND SET-UP

READ THE USER'S MANUAL BEFORE INSTALLING THE UNIT.

«
...
8
9
10
11
12
...
»

Summary of Contents for KOMFORT EC S200

























Reviews:

No comments

Related manuals for KOMFORT EC S200

Brand: Flexit Pages: 2

Brand: Flexit Pages: 24

Brand: Allied Pages: 43

ACIQ-18FM-HH-MB

Brand: ACIQ Pages: 44

Brand: Vents Pages: 16

Brand: Salda Pages: 28

Brand: MrCool Pages: 10

Brand: Ventus Pages: 66

VOLCANO VR Mini

Brand: VTS Medical Systems Pages: 21

Brand: VTS Medical Systems Pages: 24

Brand: VTS Medical Systems Pages: 32

Brand: Rheem Pages: 40

Brand: Rheem Pages: 56

Brand: Rheem Pages: 56

Brand: Rheem Pages: 36

Brand: Rheem Pages: 40

Tranquility Series

Brand: ClimateMaster Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands